Danfoss VLT DriveMotor FCP 106, Design Manual

Page: 38 / 82

HPS motors
Permissible radial
forces
Permissible axial forces
(IMB3)
Permissible axial
forces (IMV1)
Permissible axial
forces (IMV1)
Both directions Force upwards Force downwards
20000 h 40000 h 20000 h 40000 h 20000 h 40000 h 20000 h 40000 h
Motor size
Speed
[RPM]
F rad [N] F rad [N] F ax [N] F ax [N] F ax [N] F ax [N] F ax [N] F ax [N]
71
1500 580 465 330 250 350 275 300 240
1800 520 420 295 225 315 250 270 215
3000 460 370 230 175 260 205 210 170
3600 415 335 205 155 235 185 190 150
90
1500 940 750 480 365 470 385 440 330
1800 845 675 430 330 420 345 395 300
3000 670 535 340 260 380 315 310 235
3600 600 480 305 235 340 285 280 210
112
1500 1300 1040 680 540 750 630 600 450
1800 1170 935 610 485 675 565 540 405
3000 930 745 480 380 560 475 400 300
3600 835 670 430 340 505 430 360 270
132 M
1500 – – – – – – – –
1800 1710 1370 1015 790 1190 985 835 630
3000 1350 1080 800 625 1000 845 610 460
3600 1215 970 720 565 900 760 550 415
132 XL
1500 1970 1575 1090 850 1300 1080 890 670
1800 – – – – – – – –
3000 1400 1120 780 610 990 835 580 435
3600 1260 1010 700 550 890 750 520 390
132 XXL
1500 1970 1575 1090 850 1300 1080 890 670
1800 1770 1415 980 765 1170 970 800 600
3000 1400 1120 780 610 990 835 580 435
3600 1260 1010 700 550 890 750 520 390
Table 3.7 Permissible Forces, HPS Motors
Permissible radial forces: Load point corresponding to half-shaft extension, 0 axial force assumed.
Permissible axial forces: 0 radial force assumed.
Permissible loads of simultaneous radial and axial forces can be supplied on request.
Motor type Motor frame size Lubrication type Temperature range
Asynchronous 80–180
Lithium basis -40 to +140
°
C (-40 to +280
°
F)
PM 71–160
Table 3.8 Lubrication
Motor frame
size Speed
[RPM]
Bearing type, asynchronous motors Bearing type, PM motors
Drive end Non-drive end Drive end Non-drive end
71 1500/3000 – – 6205 2ZC3 6303 2ZC3
80 1500/3000 6204 2ZC3 6204 2ZC3 – –
90 1500/3000 6205 2ZC3 6205 2ZC3 6206 2ZC3 6205 2ZC3
100 1500/3000 6206 2ZC3 6206 2ZC3 – –
112 1500/3000 6306 2ZC3 6306 2ZC3 6208 2ZC3 6306 2ZC3
132 1500/3000 6208 2ZC3 6208 2ZC3 6309 2ZC3 6208 2ZC3
160 1500/3000 1) 1) – –
180 1500/3000
1) 1)
– –
Table 3.9 Standard Bearing References and Oil Seals for Motors
1) Data available at future release.
System Integration
VLT
®
DriveMotor FCP 106/FCM 106
36 Danfoss A/S © 06/2016 All rights reserved. MG03M202
3 3