Danfoss VLT Brook Crompton Motor FCM 300 Design Manual Download Page 18

Page: 18 / 102

2.1.5 Screw Sizes

Cover (lid) screws

Earth Ground and Cable Clamp screws (FCM 305-340):

Earth Ground and Cable Clamp screws (FCM 355-375)

Table 2.8

2.1.6 Protection

•

Thermal overload protection of motor and
electronics.

•

Monitoring of the intermediate circuit voltage
ensures that the inverter cuts out if the
intermediate circuit voltage gets too high or too
low.

•

If a mains phase is missing, the inverter will cut
out when a load is placed on the motor.

Illustration 2.2 Terminal Arrangement (for Installation see Quick Setup, MG03AXYY)

Installation

VLT

DriveMotor FCM Series

MG03BA02 - VLT

is a registered Danfoss trademark

Summary of Contents for VLT Brook Crompton Motor FCM 300







































































































Search results

Summary of Contents for VLT Brook Crompton Motor FCM 300

Reviews:

Related manuals for VLT Brook Crompton Motor FCM 300

Brands by name

Popular brands

Danfoss VLT Brook Crompton Motor FCM 300, Design Manual

Search results

Summary of Contents for VLT Brook Crompton Motor FCM 300

Reviews:

Related manuals for VLT Brook Crompton Motor FCM 300

Brands by name

Popular brands