Danfoss VLT AutomationDrive FC 302, Programming Manual, Page: 323 / 346

5.3.27 42-** Safety Functions
Par.
No. #
Parameter description Default value 4-set-up FC 302
only
Change
during
operation
Conver-
sion index
Type
42-1* Speed Monitoring
42-10 Measured Speed Source ExpressionLimit 1 set-up FALSE - Uint8
42-11 Encoder Resolution 1024 N/A 1 set-up FALSE 0 Uint16
42-12 Encoder Direction [0] Clockwise 1 set-up FALSE - Uint8
42-13 Gear Ratio 1 N/A 1 set-up FALSE -4 Uint32
42-14 Feedback Type [0] With direction info 1 set-up FALSE - Uint8
42-15 Feedback Filter 200 Hz 1 set-up FALSE -2 Uint16
42-17 Tolerance Error 120 RPM 1 set-up FALSE 67 Uint16
42-18 Zero Speed Timer 8760 h 1 set-up FALSE 74 Uint16
42-19 Zero Speed Limit 120 RPM 1 set-up FALSE 67 Uint16
42-2* Safe Input
42-20 Safe Function ExpressionLimit 1 set-up FALSE - Uint8
42-21 Type [0] NCNC 1 set-up FALSE - Uint8
42-22 Discrepancy Time 10 ms 1 set-up FALSE -3 Uint16
42-23 Stable Signal Time 10 ms 1 set-up FALSE -3 Uint16
42-24 Restart Behaviour [0] Manual 1 set-up FALSE - Uint8
42-3* General
42-30 External Failure Reaction [0] STO 1 set-up FALSE - Uint8
42-31 Reset Source [0] Drive Reset 1 set-up FALSE - Uint8
42-33 Parameter Set Name ExpressionLimit 1 set-up FALSE 0
VisStr[
8]
42-35 S-CRC Value ExpressionLimit 1 set-up FALSE 0 Uint16
42-36 Level 1 Password ExpressionLimit 1 set-up FALSE 0
VisStr[
8]
42-37 Level 1 Password Buffer ExpressionLimit 1 set-up FALSE 0
VisStr[
8]
42-4* SS1
42-40 Type [0] Delay 1 set-up FALSE - Uint8
42-41 Ramp Profile [0] Linear 1 set-up FALSE - Uint8
42-42 Delay Time 1 s 1 set-up FALSE -1 Uint16
42-43 Delta T 2 % 1 set-up FALSE 0 Uint8
42-44 Deceleration Rate 1500 /s 1 set-up FALSE 0 Uint16
42-45 Delta V 120 RPM 1 set-up FALSE 67 Uint16
42-46 Zero Speed 10 RPM 1 set-up FALSE 67 Uint16
42-47 Ramp Time 1 s 1 set-up FALSE -1 Uint16
42-48 S-ramp Ratio at Decel. Start 50 % 1 set-up FALSE 0 Uint8
42-49 S-ramp Ratio at Decel. End 50 % 1 set-up FALSE 0 Uint8
42-5* SLS
42-50 Cut Off Speed 270 RPM 1 set-up FALSE 67 Uint16
42-51 Speed Limit 150 RPM 1 set-up FALSE 67 Uint16
42-52 Fail Safe Reaction [0] STO 1 set-up FALSE - Uint8
42-53 Start Ramp [0] No 1 set-up FALSE - Uint8
42-54 Ramp Down Time 1 s 1 set-up FALSE -1 Uint16
42-6* Safe Fieldbus
42-60 Telegram Selection [0] None 1 set-up FALSE - Uint8
42-61 Destination Address 1 N/A 1 set-up FALSE 0 Uint16
42-8* Status
42-80 Safe Option Status 0 N/A All set-ups TRUE 0 Uint32
42-81 Safe Option Status 2 0 N/A 1 set-up TRUE 0 Uint32
42-82 Safe Control Word 0 N/A All set-ups TRUE 0 Uint32
42-83 Safe Status Word 0 N/A All set-ups TRUE 0 Uint32
42-85 Active Safe Func. [10] None All set-ups TRUE - Uint8
42-86 Safe Option Info 0 N/A All set-ups TRUE 0
VisStr[
25]
42-87 Time Until Manual Test 8761 h All set-ups TRUE 74 Uint16
42-88 Supported Customization File Version ExpressionLimit 1 set-up TRUE -2 Uint16
42-89 Customization File Version ExpressionLimit 1 set-up TRUE -2 Uint16
42-9* Special
42-90 Restart Safe Option [0] No All set-ups FALSE - Uint8
Table 5.14
Parameter Lists Programming Guide
MG33MP02 Danfoss A/S © 10/2018 All rights reserved. 321
5 5