VLT
®
8000 AQUA
Installation
■
Technical data, mains supply 3 x 200 - 240 V
According to international requirements
VLT type
8016
8022
8027
8032
8042
8052
8062
Output current
4)
I
VLT,N
[A]
(200-230 V)
46.2
59.4
74.8
88.0
115
143
170
I
VLT, MAX
(60 s)
[A] (200-230 V)
50.6
65.3
82.3
96.8
127
158
187
I
VLT,N
[A] (240 V)
46.0
59.4
74.8
88.0
104
130
154
I
VLT, MAX
(60 s)
[A] (240 V)
50.6
65.3
82.3
96.8
115
143
170
Output power
S
VLT,N
[kVA]
(240 V)
19.1
24.7
31.1
36.6
41.0
52.0
61.0
Typical shaft
output
P
VLT,N
[kW]
11
15
18.5
22
30
37
45
Typical shaft
output
P
VLT,N
[HP]
15
20
25
30
40
50
60
Max. cable
cross-section
to motor and
DC-bus [mm
2
]/[AWG]
2) 5)
Copper
Aluminium
6)
16/6
16/6
35/2
35/2
35/2
35/2
50/0
50/0
70/1/0
95/3/0
5)
95/3/0
90/250
mcm
5)
120/4/0
120/300
mcm
5)
Min. cable cross-section to motor
and DC-bus [mm
2
]/[AWG]
2)
10/8
10/8
10/8
16/6
10/8
10/8
10/8
Max. input current (200 V) (RMS)
I
L,N
[A]
46.0
59.2
74.8
88.0
101.3
126.6
149.9
Max. cable
cross-section
power [mm
2
]/[AWG]
2) 5)
Copper
Aluminium
6)
16/6
16/6
35/2
35/2
35/2
35/2
50/0
50/0
70/1/0
95/3/0
5)
95/3/0
90/250
mcm
5)
120/4/0
120/300
mcm
5)
Max. pre-fuses
[-]/UL
1)
[A]
60
80
125
125
150
200
250
Efficiency
3)
0.95
0.95
0.95
0.95
0.95
0.95
0.95
Weight IP
00/Chassis
[kg/lbs]
-
-
-
-
90/198
90/198
90/198
Weight IP
20/NEMA 1
[kg/lbs]
23/51
30/66
30/66
48/106 101/223
101/223
101/223
Weight IP 54
[kg/lbs]
38/84
49/108
50/110
55/121 104/229
104/229
104/229
Power loss at
max. load.
[W]
545
783
1042
1243
1089
1361
1613
Enclosure
IP 00/IP 20/NEMA 1/IP 54/NEMA 12
1. For type of fuse, see section
Fuses
.
2. American Wire Gauge.
3. Measured using 30 m/100 ft screened motor cables at rated load and rated frequency.
4. Current ratings fulfill UL requirements for 208-240 V.
5. Connection stud 1 x M8 / 2 x M8.
6. Aluminium cables with cross section above 35 mm
2
must be connected by use of an Al-Cu connector.
MG.83.A2.02 - VLT is a registered Danfoss trademark
37