VLT
®
5000 FLUX
Programming
■
Digital Input Functions
Digital inputs
Terminal no.
16
17
18
19
27
29
32
33
parameter
300 301
302 303 304 305
306 307
Value:
(Operating Command Group)
No function
(NO OPERATION)
[0]
[0]
[0]
[0]
[0]
[0]
[0]
Reset
(RESET)
[1]*
[1]
[1]
[1]
[1]
Coasting stop, inverse
(COAST INVERSE)
[0]*
Reset and coasting stop, inverse
(COAST & RESET INVERS)
[1]
Quick-stop, inverse
(QSTOP INVERSE)
[2]
DC-braking, inverse
(DCBRAKE INVERSE)
[3]
Stop inverse
(STOP INVERSE)
[2]
[2]
[4]
[2]
[2]
[2]
Start
(START)
[1]*
Latched start
(LATCHED START)
[2]
Reversing
(REVERSING)
[1]*
Start reversing
(START REVERSE)
[2]
Only start clockwise, on
(ENABLE START FWD.)
[3]
[3]
[3]
[3]
Only start anti-clockwise, on
(ENABLE START REV)
[3]
[3]
[4]
[3]
Jog
(JOGGING)
[4]
[4]
[5]*
[4]
[4]
Preset reference, on
(PRESET REF. ON)
[5]
[5]
[6]
[5]
[5]
Preset reference, lsb
(PRESET REF. SEL. LSB)
[6]
[7]
[6]
Preset reference, msb
(PRESET REF. MSB)
[6]
[8]
[6]
Freeze reference
(FREEZE REFERENCE)
[7]
[7]*
[9]
[7]
[7]
Freeze output
(FREEZE OUTPUT)
[8]
[8]
[10]
[8]
[8]
Speed up
(SPEED UP)
[9]
[11]
[9]
Speed down
(SPEED DOWN)
[9]
[12]
[9]
Choice of Setup, lsb
(SETUP SELECT LSB)
[10]
[13]
[10]
Choice of Setup, msb
(SETUP SELECT MSB)
[10]
[14]
[10]
Choice of Setup, msb/speed up
(SETUP MSB/SPEED UP)
[11]*
Choice of Setup, lsb/speed down
(SETUP LSB/SPEED DOWN)
[11]*
Catch-up
(CATCH UP)
[11]
[15]
[12]
Slow-down
(SLOW DOWN)
[11]
[16]
[12]
Ramp 2
(RAMP 2)
[12] [12]
[17]
[13]
[13]
Mains failure inverted
(MAINS FAILURE INVERSE)
[13] [13]
[18]
[14]
[14]
Pulse reference
(PULSE REFERENCE)
[28]
Function:
Description of choice:
No function
The frequency converter does not react
to signals transmitted to the terminal.
Reset
Resetting the frequency converter after a
TRIP/ALARM; however not all alarms can be reset.
Coasting stop (terminal 27)
Inverted input (NC).
The frequency converter leaves the motor in free
mode. Logic
’
0
’
=> coasting stop.
Reset and coasting stop (terminal 27)
Inverted
input (NC). The frequency converter leaves the
motor in free mode and successive resets the drive.
Logic
’
0
’
=> coasting stop and reset.
Quick-stop inverted (terminal 27)
Inverted input
(NC). Generates stop in accordance with the quick-stop
ramp time (Parameter 212). When the motor is stopped
the shaft is then in free mode. Logic
’
0
’
=> Quick-stop.
DC braking inverted (terminal 27)
Inverted input
(NC). Stopping the motor by energizing it with a DC for
a certain time. See parameter 125-127. The function
is only active when the value in parameter 126 is
different from 0. . Logic
’
0
’
=> DC braking.
✭
= factory setting. () = display text [] = value for use in communication via serial communication port
MG.55.A6.02 - VLT is a registered Danfoss trademark
89