background image

Start

position

Length

Name

SPN

5.1

2 bits

Force feedback error status
0x00: No error
0x01: POST Error
0x02: Online Error
0x03: Missing incoming EHD Communication
(FF disabled)

NA

5.3

2 bits

OPN error status
0x00: NO Error
0x01: POST Error
0x02: Online Error
0x03: Missing incoming EHD communication (OPN active)

NA

5.5

2 bits

Joystick Y-Axis Detent Position Status
(Used for Force Feedback status)
0x00: Active
0x01: Not Active
0x02: Error Indicator (refer to bits 5.1..2 for reason)
0x03: Not Available

2681

5.7

2 bits

Joystick X-Axis Detent Position Status
(Used for OPN status)
0x00: Active
0x01: Not Active
0x02: Error Indicator (refer to bits 5.3..4 for reason)
0x03: Not Available

2680

6.1

2 bits

Joystick 1 Button 4 Pressed Status (Auto-Guidance)
0x00: Not pressed
0x01: Pressed
0x02: Error Indicator
0x03: Not Available

2688

6.3

2 bits

Joystick 1 Button 3 Pressed Status (Indicator Right)
0x00: Not pressed
0x01: Pressed
0x02: Error Indicator
0x03: Not Available

2687

6.5

2 bits

Joystick 1 Button 2 Pressed Status (Indicator Left)
0x00: Not pressed
0x01: Pressed
0x02: Error Indicator
0x03: Not Available

2686

6.7

2 bits

Joystick 1 Button 1 Pressed Status (H/L beam)
0x00: Not pressed
0x01: Pressed
0x02: Error Indicator
0x03: Not Available

2685

The joystick will transmit SAE-J1939 messages every 50 ms per CAN channel.

Operation modes

JS1-H Steer by Wire implements different operating modes in software:

1. Bootloader Mode
2. Normal Operation
3. Safe State

User and Safety Manual

PLUS+1® JS1-H Steer by Wire

Steer by Wire Joystick

 

©

 Danfoss | December 2022

AX436683569858en-000101 | 13

Summary of Contents for PLUS+1 JS1-H


























Reviews: