background image

© Danfoss |2017.06

VI.LV.H1.02 | 1

ECL Comfort 296 / 310 controllers

Modbus networking guide

Service Guide

1.0   Contents

1.0   Contents... .  ................................................................................................................................................................................................................................................1
2.0   Introduction .............................................................................................................................................................................................................................................2
3.0   Conclusion ... .............................................................................................................................................................................................................................................2
4.0   Modbus network definitions  .............................................................................................................................................................................................................3

4.1    Multipoint serial bus infrastructure .......................................................................................................................................................................................3

5.0   ECL 296 / 310 Modbus network specification .............................................................................................................................................................................4
6.0   Installation class and surge / lightning protection ....................................................................................................................................................................5
7.0   Annexure A:  Modbus network wiring guidelines ......................................................................................................................................................................6

7.1   Central heating station ................................................................................................................................................................................................................7
7.2    Repeater stations (individual houses with repeater) .......................................................................................................................................................8
7.3    Individual houses (without repeater) ....................................................................................................................................................................................9

8.0   Annexure B ............................................................................................................................................................................................................................................ 10

8.1    Selection of parts ........................................................................................................................................................................................................................10
8.2    Surge protector wiring..............................................................................................................................................................................................................11
8.3    “Modbus” to “mains” separation ...........................................................................................................................................................................................12

Summary of Contents for ECL Comfort 310

















Reviews: