Danfoss AKD 2800, Quick Setup Manual, Page: 28 / 77

AKD 2800
■
Inputs and outputs
D
D D
Diiiig
g g
giiiitttta
a a
allll iiiin
n n
np
p p
pu
u u
utttts
s s
s T
T T
Te
e e
errrrm
m m
m.... n
n n
no
o o
o.... 1
1 1
18
8 8
8
1
1 1
1
1
1 1
19
9 9
9
1
1 1
1
2
2 2
27
7 7
7 2
2 2
29
9 9
9 3
3 3
33
3 3
3
p p p pa a a arrrr.... n n n no o o o.... 3 3 3 30 0 0 02 2 2 2 3 3 3 30 0 0 03 3 3 3 3 3 3 30 0 0 04 4 4 4 3 3 3 30 0 0 05 5 5 5 3 3 3 30 0 0 07 7 7 7
Value:
No function
(NO OPERATION) [0] [0] [0] [0]
✭
[0]
Reset (RESET) [1] [1] [1] [1] [1]
Coasting stop inverse (MOTOR COAST INVERSE) [2] [2] [2] [2] [2]
Reset and coasting inverse (RESET AND COAST INV.) [3] [3]
✭
[3] [3] [3]
Quick-stop inverse (QUICK-STOP INVERSE) [4] [4] [4] [4] [4]
DC braking inverse (DC-BRAKE INVERSE) [5] [5] [5] [5] [5]
Stop inverse (STOP INVERSE) [6] [6] [6] [6] [6]
Start (START)
✭
[7] [7] [7] [7] [7]
Pulse start (LATCHED START) [8] [8] [8] [8] [8]
Reversing (REVERSING) [9]
✭
[9] [9] [9] [9]
Reversing and start (START REVERSING) [10] [10] [10] [10] [10]
Start clockwise (ENABLE FORWARD) [11] [11] [11] [11] [11]
Start anti-clockwise (ENABLE REVERSE) [12] [12] [12] [12] [12]
Jog (JOGGING) [13] [13] [13]
✭
[13] [13]
Freeze reference (FREEZE REFERENCE) [14] [14] [14] [14] [14]
Freeze output frequency (FREEZE OUTPUT) [15] [15] [15] [15] [15]
Speed up (SPEED UP) [16] [16] [16] [16] [16]
Speed down (SPEED DOWN) [17] [17] [17] [17] [17]
Catch-up (CATCH-UP) [19] [19] [19] [19] [19]
Slow-down (SLOW-DOWN) [20] [20] [20] [20] [20]
Ramp 2 (RAMP 2) [21] [21] [21] [21] [21]
Preset ref, LSB (PRESET REF, LSB) [22] [22] [22] [22] [22]
Preset ref, MSB (PRESET REF, MSB) [23] [23] [23] [23] [23]
Preset reference on (PRESET REFERENCE ON) [24] [24] [24] [24] [24]
Thermistor (THERMISTOR) [25] [25] [25] [25]
Precise stop, inverse (PRECISE STOP INV.) [26] [26]
Precise start/stop (PRECISE START/STOP) [27] [27]
Pulse reference (PULSE REFERENCE) [28]
Pulse feedback (PULSE FEEDBACK) [29]
Pulse input (PULSE INPUT) [30]
Selection of Setup, lsb (SETUP SELECT LSB) [31] [31] [31] [31] [31]
Selection of Setup, msb (SETUP SELECT MSB) [32] [32] [32] [32] [32]
Reset and start (RESET AND START) [33] [33] [33] [33] [33]
Pulse counter start (PULSE COUNTER START) [34] [34]
1. All functions on terminal 18 and 19 are controlled
by an interrupter, which means that the repetitive
accuracy of the response time is constant. Can be
used for start/stop, setup switch and especially for
changing digital preset, i.e. to obtain a reproducable
stop point when using creep speed.
✭
= factory setting. () = display text [] = value for use in communication via serial communication port
MG.28.H2.02 -
28