AKD 2800
Programming
Function:
The active parameter Setup is selected here. All
parameters can be programmed in four individual
parameter Setups. Shifts between Setups can
be made in this parameter via a digital input
or via serial communication.
Description of choice:
Factory Setup
[0] contains the factory-set parameter
values.
Setup 1-4
[1]-[4] are four individual
Setups which can be selected as required.
Multi
Setup
[5] is used where remote-controlled shifts
between the four Setups via a digital input or via
serial communication is required.
005 Programming Setup
(EDIT SETUP)
Value:
Factory Setup (FACTORY SETUP)
[0]
Setup 1 (SETUP 1)
[1]
Setup 2 (SETUP 2)
[2]
Setup 3 (SETUP 3)
[3]
Setup 4 (SETUP 4)
[4]
✭
Active Setup (ACTIVE SETUP)
[5]
Function:
You can select which Setup you want to programme
during operation (applies both via the control
panel and the serial communication port). It is,
for example, possible to programme
Setup 2
[2], while the active Setup is set to
Setup 1
[1]
in parameter 004
Active Setup
.
Description of choice:
Factory Setup
[0] contains the factory-set data and can
be used as a source of data if the other Setups are to be
reset to a known status.
Setup 1-4
[1]-[4] are individual
Setups that can be programmed freely during operation.
If
Active Setup
[5] is selected, the programming Setup
will be equal to parameter 004
Active Setup
.
NB!:
If data is modified or copied to the active
Setup, the modifications have an immediate
effect on the unit
’
s operation.
006 Setup copying
(SETUP COPY)
Value:
✭
No copying (NO COPY)
[0]
Copy to Setup 1 from #
(COPY TO SETUP 1 )
[1]
Copy to Setup 2 from #
(COPY TO SETUP 2)
[2]
Copy to Setup 3 from #
(COPY TO SETUP 3)
[3]
Copy to Setup 4 from #
(COPY TO SETUP 4)
[4]
Copy to all Setups from # (COPY TO ALL)
[5]
Function:
You can copy from the selected active Setup in
parameter 005
Programming setup
to the selected
Setup or Setups in this parameter.
NB!:
Copying is only possible in Stop (motor stopped
in connection with a stop command).
Description of choice:
Copying begins when the required copying function
has been selected and the [OK]/[CHANGE DATA]
key has been pushed. The display indicates
when copying is in progress.
007 LCP copy
(LCP COPY)
Value:
✭
No copying (NO COPY)
[0]
Upload all parameters (UPL. ALL PAR.)
[1]
Download all parameters (DWNL. ALL PAR.)
[2]
Download size-independent parameters
( DWNL.OUTPIND.PAR.)
[3]
Function:
Parameter 007
LCP copy
is used if you want to use
the LCP 2 control panel
’
s integral copy function. The
function is used if you want to copy all parameter
setups from one frequency converter to another
by moving the LCP 2 control panel.
Description of choice:
Select
Upload all parameters
[1] if you want all
parameter values to be transferred to the control panel.
Select
Download all parameters
[2] if all parameter
values transferred are to be copied to the frequency
converter to which the control panel is attached. Select
Download size-independent par.
[3] if you only want
to downloade the size-independent parameters. This
is used when downloading to a frequency converter
with a different rated power size than that from
which the parameter setup originates.
✭
= factory setting. () = display text [] = value for use in communication via serial communication port
MG.28.H2.02 -
13