manualshive.com logo in svg

Danaher Motion P70360, Reference Manual, Page: 28 / 56

Share
Download
Danaher Motion P70360 Reference Manual Download Page 28

Using P7000Tools 

04/06 

Danaher Motion 

4.4.1 STATUS 

SCREEN 

Double-click to
reset to zero

 

System Status 

Disconnected 

Not online with the drive. Indicator off. 

Disabled 

Drive blinking green indicates online, but not enabled. 

Ready 

Drive online and enabled. Solid green indicator. 

Output State 

Offline 

Not connected to a drive. Indicator gray. 

Online 

Indicator is green when programmed output condition is met. 

Fault History 

List of the last nine drive faults. #1 being the most recent, #8 
is the oldest. 

Input States

  Indicator is green if the input is true, gray if false. 

Commanded 
Position 

Actual motor position in user units (double-click in box to 
reset to zero). 

Drive Information 

Drive Type 

Model number for this drive. 

Serial Number 

Serial number for this drive. 

OS Version 

Current firmware revision level. 

Drive Temp 

Drive temperature in degrees Celsius. 

Bus Voltage 

DC Bus Voltage 

24 Rev 

D 

M-SD-7AC-01 

Summary of Contents for P70360

























































Reviews:

No comments