manualshive.com logo in svg

DANA SPICER TM4 SUMO HP HV Powertrain, Troubleshooting Manual

Share
Download
DANA SPICER TM4 SUMO HP HV Powertrain Troubleshooting Manual Download Page 35

 

 

 

35 

Service Codes 

TT01 

 
 
 
 
 
 
 
 
 
 
 
 
 

Description 

 
The Troubleshooting Tree 01 indicates that the event 
log has been cleared. 
 
This  SysFile  ID  could  be  raised  on  the  subsequent 
power  up  if  the  MCU  was  switched  OFF  before  the 
“ReadyToPowerOff”  CAN  status  on  a  shutdown 
sequence. The potential result of this SysFile ID could 
be a loss of all the SysFile IDs previously recorded in 
the MCU. 
 
If  SysFile  section  was  corrupted,  the  SysFile  is 
cleared. In this case, a followed warning (SysFile ID 
0x000A) will  indicate  more  detail  upon nature of the 
clearance of the SysFile. See Subtree TT02. 
 

MCU power off 

 
The 

MCU 

shall 

indicate 

the 

status 

“ReadyToPowerOff”  via  the  CAN  bus  before 
disconnecting power from the Auxiliary vehicle battery 
(Vaux).  If  the  power  is  switched  off  before  this  CAN 
status, this SysFile ID can be raised. 

 
 

Note:

 A manual SysFile reset by an advance user can 

also cause the SysFile to be cleared. 
 

Note

: On MCU shutdown sequence 

The SysFile gets written in the unit EEPROM memory 
upon a shutdown sequence. If the Vaux power (12 V 
or  24  V)  is  removed  before  the  MCU  is  in 
« ReadyToPowerOff »  state  via  CAN,  the  SysFile 
section  could  possibly  get  corrupted  and  will  be 
cleared on the next power ON. 
 

Note

:  Refer  to  the  Dana  TM4  Product  installation 

guide 

for 

more 

details 

on 

installation 

and 

deinstallation  procedure  including  safety  warning 
considerations. 
 

Note

:  Refer  to  the  TM4  CAN  protocol  document  for 

correct MCU shutdown sequence. 
 
To correctly diagnose the faulty system, connect the 
Diagnostic  Tool  (see  «Diagnostics»  section  for  test 
equipment  and  descriptions)  and  follow  the 
Troubleshooting Tree procedure below. 
 
See  “Safety  Warnings”  and  “Troubleshooting  Tips” 
sections for general guidelines on system diagnostics. 
 

 

System Mode 

Referred by SysFile 
ID 

Condition 

Possible Causes 

Operational 

0x0000 

Indicates that the 
SysFile event list has 
been automatically 
cleared. 

1. 

Wrong shutdown sequence. Auxiliary 

vehicle battery (Vaux) (12V or 24V) 
powered OFF before the MCU 
“ReadyToPowerOff” CAN status on a 
shutdown sequence. 

2. 

Manual SysFile reset by an advance user. 

3. 

Defective MCU.

 

Summary of Contents for SPICER TM4 SUMO HP HV Powertrain

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands