manualshive.com logo in svg

DANA SPICER PACCAR 220ev, Troubleshooting Manual, Page: 707 / 761

Share
Download
DANA SPICER PACCAR 220ev Troubleshooting Manual Download Page 707

 

 

 

 

 

707 

Troubleshooting 

F0139 - Potential High Voltage Hazard! ePTO HVIL Fault 

Error Description 

Possible Causes 

Possible Solutions 

ePTO has reported a discontinuity 

in the HVIL. 

1)  HV connector unplugged. 

2)  Defective HV connector or 

harness. 

3)  Analog HVIL fault. 

 

1)  Plug in HV connector. 

2)  Replace HV harness. 

3)  Troubleshoot specific error. 

 

The purpose of the HVIL is to provide a warning if 

any HV connector is unplugged without the HV 

distribution being safely ended. The ePTO monitors 

continuity between the HVIL pins on its HV 

connector (C722). If this connector is unplugged 

unsafely, the HVIL will be broken and the ePTO will 

send an error message via CAN. 

 

Depending on the ePTO configuration, the ePTO HV 

connector (C722) may also be connected to the 

analog HVIL. This a single circuit that runs through 

various HV connectors on the vehicle. If a connector 

is unplugged, the HVIL will be broken and the VCU 

will detect the loss of signal voltage on the circuit. If 

the analog HVIL is broken, one or more of the errors 

F0061, F0062, or F0063 will be raised. 

 

 

Note:

 Connectors may vary from what is 

shown depending on ePTO configuration. 

 

 

Connector C722 

 

 

 

3 

4 

Summary of Contents for SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments