DANA SPICER PACCAR 220ev Troubleshooting Manual Download Page 690

Page: 690 / 761

690

Troubleshooting

Telemetry System

The telemetry system collects and transmits

operational data from the various vehicle systems to

remote servers where they can be accessed by

operators for monitoring purposes.

Component descriptions

Telemetry

The telemetry module collects data from the vehicle

systems and transmits it to remote servers via the

modem. It is powered by 12V low voltage and

communicates via the CAN B network.

Modem

The modem manages wireless communications

between the telemetry module and the remote

server. It is powered by 12V low voltage.

Timed Relay

The timed relay powers on the telemetry module and

modem at fixed intervals to collect and transmit data.

Summary of Contents for SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

DANA SPICER PACCAR 220ev, Troubleshooting Manual, Page: 690 / 761

Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews: