DANA SPICER PACCAR 220ev Troubleshooting Manual Download Page 316

Page: 316 / 761

316

Troubleshooting

HMI displays or logs

Fault code F0100 and

Traction inverter fault reason 3

Disconnect connector C3 from

the traction inverter.

Refer to the connector

investigation subtree.

Yes

Is there any connector

integrity issue?

Reconnect connector C3 to

the traction inverter.

Turn ignition ON.

Yes

Complete.

Defective connector.

Replace the connector as described in the

“Wire Harness Connector Identification,

Location, and Service Chart” in the

Service Manual.

Defective traction inverter.

Replace traction inverter.

WARNING:

Electrical hazard.

Follow Safety Warnings and High

Voltage Shutdown Procedures

defined in the Service Manual

and Diagnostic Guide.

Is the error

message still

appearing on the

HMI?

Summary of Contents for SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

DANA SPICER PACCAR 220ev, Troubleshooting Manual, Page: 316 / 761

Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews: