DANA SPICER PACCAR 220ev Troubleshooting Manual Download Page 305

Page: 305 / 761

305

Troubleshooting

Is there any evidence

of a short circuit?

Yes

Defective harness.

Replace harness.

Replace fuse F5 from MPDM.

Replace relay K004.

Did fuse F5 blow

again during test

drive?

Yes

Contact Dana for further

investigation.

Complete

With a multimeter, check for short circuit between the

following points:

-LV short: Resistance measurement is less than 100k-

ohms.

-Inspect all connectors and wires between the two test

points of the harness ends.

Pin H

GND strip1

C11 MPDM Ground

Connector pin

Continued from previous page

Reconnect all previously

disconnected connectors.

Restart the vehicle.

Summary of Contents for SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

DANA SPICER PACCAR 220ev, Troubleshooting Manual, Page: 305 / 761

Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews: