DANA SPICER PACCAR 220ev Troubleshooting Manual Download Page 186

Page: 186 / 761

186

Troubleshooting

If possible, connect another compatible

EVSE to the vehicle and restart charge. If no

other EVSE is available, unplug the faulty

EVSE from the grid and let it reinitialize

before restarting charge.

Yes

Complete

Investigate the shop power

for operation interruptions

during charge.

Could you find any

defect with shop

power supply?

Yes

Complete

Contact Dana for further

investigation.

HMI displays or logs

Fault code F0005 and Charge end reason 12

Fault code F0006 and Charge end reason 12

Fault code F0007 and Charge end reason 12

Unplug charger.

Is the vehicle able to

charge completely to

100% without raising the

same fault?

Summary of Contents for SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

DANA SPICER PACCAR 220ev, Troubleshooting Manual, Page: 186 / 761

Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews: