DANA Brevini Posiplan BPH Series Installation And Maintenance Manual Download Page 36

Page: 36 / 40

Dana Incorporated

IIMM-0005EN Posiplan (MT-5215-0806)

TROUBLESHOOTING:

Use the following table to troubleshoot any faults or malfunctions. If the problem persists, contact your nearest Brevini Service
Centre (see "SERVICE NETWORK p. 38").

PROBLEM

POSSIBLE CAUSE

SOLUTION

With motor running the output shaft doesn't
turn

Incorrect motor assembly

Check coupling between gear unit motor

Internal malfunction

Contact a Dana Incorporated Service Centre

Brake blocked

Check command circuit

Oil leak from breather during operation

Level too high

Lower oil leve

Incorrect breather position

Check breather position

Oil leak from seals

Clogged breather plug

Unscrew and thorougly clean the plug

Stiffening of seals due to prolonged storage

Clean the area and check for leakage again
after a few days

Damaged or worn seals

Contact a Dana Incorporated Service Centre

Excessive vibrations

Gear unit incorrectly installed

Check machine shaft

Not anchored securely enough

Strengthen the structure

Internal malfunction

Contact a Dana Incorporated Service Centre

Excessive noise

No lubricant

Check

Internal malfunction

Contact a Dana Incorporated Service Centre

Excessive heating

No ventilation

Remove fairing

High thermal power

Insert oil circulation

Summary of Contents for Brevini Posiplan BPH Series









































Search results

Summary of Contents for Brevini Posiplan BPH Series

Reviews:

Related manuals for Brevini Posiplan BPH Series

Brands by name

Popular brands

DANA Brevini Posiplan BPH Series, Installation And Maintenance Manual

Search results

Summary of Contents for Brevini Posiplan BPH Series

Reviews:

Related manuals for Brevini Posiplan BPH Series

Brands by name

Popular brands