manualshive.com logo in svg

DANA Brevini Posiplan BPH Series, Installation And Maintenance Manual

Share
Download
DANA Brevini Posiplan BPH Series Installation And Maintenance Manual Download Page 19

19

Dana Incorporated

IMM-0005EN Posiplan (MT-5215-0806)

GEAR UNIT INSTALLATION ON VARIOUS TYPES OF MACHINE SHAFT:

GEAR UNITS WITH “K” TYPE SHAFT

MACHINE SHAFT WITH SHOULDER:

Assembly:

align the axes of the gear unit female shaft (pos. 2) as much as possible with the machine male shaft (pos. 1), then bring the two 
shafts together after aligning the connecting spline.

Slot them together without exerting too much pressure on each part.

To make sure the female gear unit shaft is tight against the machine shaft use a threaded rod (pos. 4) of an appropriate size.

Now insert the inner seeger retaining ring (pos. 5) then the backplate (pos. 3). Now when you tighten the threaded rod, the two 
shafts will abut against each other (see Fig. 6).

Securing:

unscrew the threaded rod nut (pos. 4) and take it out of its seat. Replace the rod (pos. 4) with screw (pos. 6), torquing it down 
fully to the torque value shown in "Values Table Torque Setting Bolts p. 32", using an intermediate threadlocker. Dana Incorpo-
rated recommends LOCTITE 601 (see Fig. 7).

Disassembly:

remove the anchor bolt (pos. 6), the backplate (pos. 3) and retaining ring (pos. 5) from their relative seats. Turn the backplate 
over (pos. 3) and then return itto its seat in the gear unit female shaft(pos. 2) and secure it in positionwith the inner retaining ring 
(pos. 5).

Insert 2 bolts (pos. 7) into the two threaded holes on the backplate (pos. 3) (and screw them until they touch the machine shaft 
(pos. 1). Now give them alternately one full turn each (see Fig. 8).

Fig. 6

Fig. 7

1

2

5

3

4

3

6

Summary of Contents for Brevini Posiplan BPH Series









































Reviews:

No comments

Brands by name

Popular brands

Load more brands