Dalsa Genie Nano-5G Series, User Manual

Page: 66 / 204

64 • Contents Nano-5G Series GigE Vision Camera
Input Line Detection Level
lineDetectionLevel Specifies the voltage threshold required to recognize a
signal transition on an input line.
1.00
Beginner
DFNC
Threshold for TTL Threshold_for_TTL A signal below 0.8V will be detected as a Logical LOW and
a signal greater than 2.4V will be detected as a Logical
HIGH on the selected input line.
Input Line Debouncing
Period lineDebouncingPeriod Specifies the minimum delay before an input line voltage
transition is recognizing as a signal transition.
1.00
Beginner
DFNC
Output Line Source outputLineSource Selects which internal signal or event driven pulse or
software control state to output on the selected line. Note,
the LineMode feature must be set to Output. The List of
supported output line sources is product-specific. The
Event Control section provides details and timing
diagrams for the supported trigger modes.
1.00
Beginner
DFNC
Off Off Line output is Open
Software Controlled SoftwareControlled The OutputLineValue feature changes the state of the
output
Pulse on: Start of Frame PulseOnStartofFrame Generate a pulse on the start of the Frame Active event
Pulse on: Start of Exposure PulseOnStartofExposure Generate a pulse on the ExposureStart event. This option
is typically used to trigger a strobe light.
Pulse on: End of Exposure PulseOnEndofExposure Generate a pulse on the ExposureEnd event. This option is
typically used to trigger a strobe light.
Pulse on: Start of Readout PulseOnStartofReadout Generate a pulse on the ReadoutStart event.
Pulse on: End of Readout PulseOnEndofReadout Generate a pulse on the ReadoutEnd event.
Pulse on: Valid Frame
Trigger
PulseOnValidFrameTrigger Generate a pulse on the ValidFrameTrigger event.
Pulse on: Rejected Frame(s)
Trigger
PulseOnInvalidFrameTrigger Generate a pulse on the InvalidFrameTrigger event.
Pulse on: Start of
Acquisition
PulseOnStartofAcquisition Generate a pulse when the AcquisiontStart event occurs.
Pulse on: End of Acquisition PulseOnEndofAcquisition Generate a pulse when the AcquisiontStop event occurs.
Pulse on: End of Timer 1 PulseOnEndofTimer1 Generate a pulse on the TimerEnd 1 event.
Pulse on: End of Counter 1 PulseOnEndofCounter1 Generate a pulse on the CounterEnd 1 event.
Pulse on: Input 1 Event PulseOnInput1 Generate a pulse on the Input signal 1 event
Pulse on: Input 2 Event PulseOnInput2 Generate a pulse on the Input signal 2 event
Pulse on: Action 1 PulseOnAction1 Generate a pulse on the
GigEVision Action Command 1.
Pulse on: Action 2 PulseOnAction2 Generate a pulse on the
GigEVision Action Command 2.
Pulse on: Software
Command
PulseOnSoftwareCmd Generate a pulse on the Input of a Software Command
Exposure Active ExposureActive Generate a signal that is active when the Exposure is
active.
Output Line Pulse Signal
Activation outputLinePulseActivation Specifies the input line activation mode to trigger the
OutputLine pulse.
1.00
Beginner
DFNC
Rising Edge RisingEdge Specifies that the trigger is considered valid on the rising
edge of the source signal.
Falling Edge FallingEdge Specifies that the trigger is considered valid on the falling
edge of the source signal.
Any Edge AnyEdge Specifies that the trigger is considered valid on the falling
or rising edge of the source signal.
Output Line Pulse Delay outputLinePulseDelay Sets the delay (in µs) before the output line pulse signal.
Applicable for the OutputLineSource feature.
1.00
Beginner
DFNC
Output Line Pulse Duration outputLinePulseDuration Sets the width (duration) of the output line pulse in
microseconds.
1.00
Beginner
DFNC