Dalsa Everywhereyoulook Linea Lite GigE, User Manual

Page: 65 / 147

Linea Lite GigE Series Camera Operational Reference • 63
Rotary Encoder Output
Mode
rotaryEncoderOutputMode Specifies the conditions for the Rotary Encoder interface to
generate a valid Encoder output signal. Expert
DFNC
Position Position On the camera, the "position" behaviour exists, but the
number of counts is small (7-bits / 128 counts). The
encoder can reverse for 256 ticks and then go forward and
behave as expected for "position" style behaviour. If the
user exceeds 256 ticks, the count will max out, but will not
reset. When the user starts going forward again, 256 lines
will be dropped / ignored and then resume output.
Motion Motion The triggers are generated for all motion increments in
either direction.
Rotary Encoder Direction rotaryEncoderDirection Specifies the phase which defines the encoder forward
direction. Expert
DFNC
Clockwise Clockwise Inspection goes forward when the rotary encoder direction
is clockwise (phase B is ahead of phase A).
Counter Clockwise CounterClockwise Inspection goes forward when the rotary encoder direction
is counter clockwise (phase A is ahead of phase B).
Rotary Encoder Input A
Source rotaryEncoderInputASource Selects which input line to assign to the rotary encoder
input A (also known as shaft encoder). Note that the Line
Mode feature must be set to Input. The list of supported
input line sources is device-specific. Expert
DFNC
Line 1 Line1 Line1 is assigned to the Rotary Encoder Input A.
Line 3 Line3 Line3 is assigned to the Rotary Encoder Input A.
Rotary Encoder Input B
Source rotaryEncoderInputBSource Selects which input line to assign to the rotary encoder
input B (also known as shaft encoder). Note that the Line
Mode feature must be set to Input. The list of supported
input line sources is device-specific. Expert
DFNC
GND GND Rotary Encoder Input B is not used
Line 2 Line2 Line2 is assigned to the Rotary Encoder Input B
Rotary Encoder Source
Activation rotaryEncoderSrcActivation Specifies the signal edge(s) use to increment the rotary
encoder. Expert
DFNC
Rising Edge RisingEdge The rotary encoder uses the rising edge of the source
signal.
Any Edge AnyEdge The rotary encoder uses either the rising edge or falling
edge of the source signal.
Rotary Encoder Rescaler
Order rotaryEncoderRescalerOrder Specifies the order that the multiplier and divider are
applied. Guru
DFNC
Multiplier Divider multiplierDivider The signal is multiplied before been divided.
Divider Multiplier dividerMultiplier The signal is divided before been multiplied.
Rotary Encoder Multiplier rotaryEncoderMultiplier Specifies a multiplication factor for the rotary encoder
output pulse generator.
DFNC
Beginner
Rotary Encoder Divider rotaryEncoderDivider Specifies a division factor for the rotary encoder output
pulse generator.
DFNC
Beginner
Line Selector LineSelector Selects the physical line (or pin) of the external device
connector to configure.
Beginner
Line 1 Line1 Index of the physical line and associated I/O control block
to use. Pin 1 and Pin 2 is the RS-422 Input Port 1+, 1-,
respectively.
Line 2 Line2 Index of the physical line and associated I/O control block
to use. Pin 3 and Pin 4 is the RS-422 Input Port 2+ and 2-
, respectively.
Line 3 Line3 Index of the physical line and associated I/O control block
to use. Pin 6 and Pin 7 is the Port 3+ and 3-, respectively.
Line 4 Line4 Index of the physical line and associated I/O control block
to use. Pin 11 and Pin 12 is Output Port 4+ and 4-,
respectively.
Line 5 Line5 Index of the physical line and associated I/O control block
to use. Pin 13 and Pin 14 is the Output 5+ and 5-,
respectively.
Preliminary