manualshive.com logo in svg

dallmeier CasinoCam DDF3000AV, Installation And Configuration Manual

Share
Download
dallmeier CasinoCam DDF3000AV Installation And Configuration Manual Download Page 26

DDF3000AV(-DN) / DDF3000AV(-DN) CasinoCam

®

26

Dallmeier electronic

8.2.6

Day / Night Setup

The camera has a special setting that allows for detailed shots
at night. Here, the camera can be manually or automatically
set to day/night mode.

Night Control = Auto is set by default for the
DDF3000AV(-DN).

NOTE

Night Control = Off is set by default for the DDF3000AV(-DN)
CasinoCam

®

.

Do not change these settings when using the camera in a casino
environment.

‰

Night Control

Night Control = Off

The camera is set to day mode. Night mode is deactivated.

Night Control = On

This setting immediately changes the camera to night mode, regardless of the prevailing
light conditions.

Night Control = Auto

This setting automatically switches the camera to night mode at certain light conditions.

‰

Night Mode

With Night Mode, you can select whether the camera will take color or black-and-white
images at night.

‰

Night: max. Gain

Night: max. Gain allows you to fix the limit for the maximum amplitude of the video
signal in night mode.

-------- Day/Night Setup ---------

Previous Page.

>

Night Control

< Off >

Night Mode

Color

Night: max. Gain

32

Summary of Contents for CasinoCam DDF3000AV


































Reviews:

No comments

Brands by name

Popular brands

Load more brands