background image

10 

 

www.dalemans.com 

  

  

|

 

  

    

2.    INSTALLATION OF THE CONTROL UNIT 

 
 

2.1  PRECAUTIONS FOR USE 

 

For your safety, before undertaking any action, always make sure that the equipment is disconnected 
from mains power supply. 
 

The 

U•H1

 control unit

’s 

enclosure can only be opened by qualified personnel.  

 
The 

U•H1

 control unit must be placed  in a room  without  any  explosive atmosphere and within  easy 

reach.  
 
As the 

U•H1

 control unit

’s 

enclosure is reversible, it may be set up to receive electrical cables from the 

top or bottom. To guarantee optimal sealing, cables should be received from the bottom.  

The equipment must be placed in a dry and clean environment. 

A set of holes are provided in the enclosure. To install the cable glands, it is necessary to remove the 
machined parts from these holes using a flat-head screwdriver and a mallet.  

 
  

 

 

Important note:

  

Never place the 

U•H1

 control unit, the alarm and the cable for the detector in the vicinity of :   

 

-

 

a high-voltage cable or a power cable, 

-

 

coaxial cable or transmitter, 

-

 

welding station or frequency regulator. 

 

2.2  PLACEMENT OF THE U

 

H1 CONTROL UNIT 

 
The 

U•H1

 control unit must be attached to a clean and damp-free wall.  Two attachment systems, a 

drilling  diagram  and  a  quick  installation  guide  are  provided  with  the  equipment. You  can  opt  for 
attachment via the enclosure or via the 4 fixing feets provided. 

 
Optionally,  it  is  also  possible  to  attach  the 

U•H1

  control  unit  to  a  DIN  rail.  Please  contact  your 

DALEMANS SA 

representative for more information. 

If the attachment method without feet is chosen, attach the enclosure using the 4 holes located in the 
corners of the enclosure using a PZ2 screwdriver with a minimum length of 150 mm.  
For the different stages, refer to the quick installation guide provided in the packaging.  

 

Before drilling these holes using a tool, it is recommended to remove the 
electronic part to avoid any accidental damage. 

 

Summary of Contents for U-H1









































Reviews: