manualshive.com logo in svg

DALBO MINIMAX 830 2008, Manual

Share
Download
DALBO MINIMAX 830 2008 Manual Download Page 25

 
 
 

 
Fitting  

1.

 

Fit bearing outer rings pos. 17+18 in hub housing pos. 22 

2.

 

Fit seal ring pos. 16 

3.

 

Fit bearing inner ring pos. 18 on axle pos. 2 and fit axle in hub housing 

4.

 

Fit bearing inner ring pos. 17 on axle pos. 2 

5.

 

Screw castle nut onto axle pos 2, whilst turning hub housing pos. 22. Tight-
en castle nut until hub housing revolves slowly. Slacken castle nut a quar-
ter turn or until hub housing revolves easily. 

6.

 

Fit split pin pos. 20 

7.

 

Fill hub cap pos. 21 half full with ball bearing grease and fit to hub 

 

Replacing rollers 

Repairs must be performed with the roller connected to a tractor, resting on a level 
surface,  fully  extended  with  the  rings  resting  on  the  ground.  A  crane  is  recom-
mended for removal and replacement procedures.  
 
Replacing side section rollers 

 

If  no  crane  is  available,  remove  both  side  section  axles  to  prevent  roller  tipping 
over.  

 

 

Fig. 23 

1.

 

Slacken bolts (A) 

2.

 

Attach  lifting  gear  to  box  sec-
tion  arm  on  side  section. 
Tighten  straps  until  bolts  (A) 
are loose and can be removed. 

3.

 

Activate  raise/lower  cylinder, 
lift rollers from wheels 

4.

 

Rings can be rolled off roller. 

 

 

If  there  is  no  crane available,  activate roller  extend cylinder  until bolts are  loose 
and can be removed. 
 
Fitting  

1.

 

Replace rings in a position corresponding to that when the roller is extend-
ed.  

2.

 

Extend roller, dropping carefully over rings.  

3.

 

Fit bolts (A)  

 
 
 

 

Ensure  no  personnel  are  within  the  machine's  extension  radius  when  activating 
hydraulics. 

A

 

 

Summary of Contents for MINIMAX 830 2008






























Reviews:

No comments

Brands by name

Popular brands

Load more brands