manualshive.com logo in svg

DALBO MAXIROLL 1030, Manual

Share
Download
DALBO MAXIROLL 1030 Manual Download Page 7

 

 

MAXIROLL 

 

 

Page 7 

 

Hydraulics 

•

 

Lower machine fully for any repair work on the hydraulic system. Relieve hy-
draulic pressure, switch engine off and remove ignition key. 
 

•

 

Clean hydraulic connections thoroughly before reconnecting. When connecting 
hydraulic hoses to tractor hydraulics, ensure they are not under pressure. 

 

•

 

Bleed the hydraulic system thoroughly after any repairs.  
 

•

 

Check hydraulic hoses regularly for defects such as cracks, splits, crimps, wear 
or breaks. Defective hoses must be replaced immediately. 
 

•

 

Avoid spilling oil on the ground. If oil is spilt, collect and deliver to a destruction 
point. 
 

•

 

Clean hands thoroughly after  contact  with  oil  and  grease. Change  oil-stained 
clothing immediately. Hydraulic oil can be harmful to the skin. 

 

•

 

Hydraulic oil released under high pressure can penetrate the skin and cause 
severe injury. In the event of injury, seek medical help immediately. 

 

Mounting 

•

 

Danger of crushing! Ensure no personnel are between implement and tractor, 
or between the parts to be connected. 

 

Maintenance and repair  

•

 

Ensure  machine  is  adequately  supported  or  fully  extended  for  all  repair  and 
maintenance  work.  Ensure  tractor  and  machine  are  properly  braked,  engine 
stopped and ignition key removed. 

 

•

 

Tighten all screw connections after a few hours use. Check all screw connec-
tions regularly and tighten as required. Check all split pins and bolts to avoid 
mechanical failure. 

 

•

 

Dispose  of  oil,  grease and  filters  in  accordance  with  local  environmental  pro-
tection rules. 

 

Road transport 

•

 

All safety and warning precautions mandatory by law must be fitted and tested 
before transporting the machine on public roads. The driver is responsible for 
correct lighting and warning signs in accordance with traffic regulations. 

 

•

 

Check with local traffic authorities whether transport on public roads is allowed 
given the machine's dimensions.  

Summary of Contents for MAXIROLL 1030











































Reviews:

No comments

Brands by name

Popular brands

Load more brands