manualshive.com logo in svg

DALBO GREENLINE 300, Manual

Share
Download
DALBO GREENLINE 300 Manual Download Page 24

 

 

GREENLINE 

 

 

 

Side 24 

 

 

 

Activate  extend/retract  cylinders  after  fitting  until  they  show  a  little  movement. 
Reverse cylinders until they return to start position. Move cylinders backwards and 
forward several times. Raise roller fully onto wheels, extend side sections fully to 
bleed system. 
 

 

 
Ensure no personnel are within the extension radius of the side sections. 

 

Replacing gasket set for extend/retract cylinder  

Fig. 31 

 

Cylinder 80/40-350 (91805) 

 
1.

 

For  cylinder  removal,  see  ”

Replacing  extend  cylinder  for  retracting  side  secti-

ons

”.

 

2.

 

Drain oil from cylinder by moving ram carefully backwards and forwards. 

3.

 

Extend ram to centre position. Unscrew upper part (pos. 3) from cylinder tube 
(pos. 1). Use special tool to remove upper part. If upper part is stuck, heat front 
of sleeve. When upper part is detached from cylinder tube, pull ram up towards 
upper part and remove completely from cylinder tube. 

4.

 

Remove lock nut retaining collar shoe (pos. 4). 

5.

 

Remove collar shoe (pos. 4) from ram. 

6.

 

Remove upper part (pos. 3) from ram. 

7.

 

Remove gaskets in upper part and collar shoe, (pos. 5+6+7+8+9). 

8.

 

Clean  all  parts  and  check  for  particles  etc.  Check  for  rust  around  scraper  ring 
(pos. 5) in upper part. If detected, remove thoroughly. 

Summary of Contents for GREENLINE 300

































Reviews:

No comments

Brands by name

Popular brands

Load more brands