manualshive.com logo in svg

DAL-BO Maxiroll 1030 2008, Manual

Share
Download
DAL-BO Maxiroll 1030 2008 Manual Download Page 30

 

 

Maxiroll 2008 

 

 

 

Page 30 
 

 

Replacing gaskets on raise/lower cylinder 

Fig. 26 

 

 
1.

 

Drain oil from cylinder by moving ram carefully backwards and forwards. 

2.

 

Extend ram to centre position. Unscrew upper part (pos. 3) from cylinder 
tube (pos. 1). Use special tool to remove upper part. If upper part is stuck, 
heat 

front

 of upper part gently. When upper part is detached from cylinder 

tube, pull ram up towards upper part and remove completely from cylinder 
tube (pos. 1). 

3.

 

Remove lock nut (pos. 10) securing collar shoe (pos. 4). 

4.

 

Remove collar shoe (pos. 4) from ram shaft, (pos. 2). 

5.

 

Remove upper part (pos. 3) from ram shaft, (pos. 2). 

6.

 

Remove gaskets in upper part (pos. 5+6+7+8+9) along with collar shoe. 

7.

 

Clean  all parts and check for particles  etc. Check for rust around scraper 
ring (pos. 5) in upper part. If detected, remove thoroughly. 

 

Mounting 

1.

 

Fit new gaskets (pos. 5+6+7+8+9) in upper part, plus collar shoe. 

2.

 

Lubricate thread in upper part (pos. 3) and cylinder tube (pos. 1) with oil. 

3.

 

Fit upper part (pos. 3) on ram shaft. 

4.

 

 Fit collar shoe (pos. 4) and screw on lock  nut, 

secure with Loctite

. En-

sure that thread is  absolutely clean and free of oil or other impurities be-
fore applying Loctite.

 Do not fill with oil for 12 hours after use of Loc-

tite.

 

5.

 

Lubricate outer collar shoe gasket in contact with cylinder tube and inside 
of cylinder tube with oil, push ram into centre position. 

6.

 

Fit upper part onto cylinder tube and tighten. 

7.

 

For fitting cylinder see ”Replacing raise/lower cylinder”. 

 

Summary of Contents for Maxiroll 1030 2008











































Reviews:

No comments

Brands by name

Popular brands

Load more brands