manualshive.com logo in svg

DAL-BO Maxiroll 1030 2008, Manual

Share
Download
DAL-BO Maxiroll 1030 2008 Manual Download Page 25

 

 

Maxiroll 2008 

 

 

Page 25 

Adjustment  

Adjustment of rollers 

After the first season, the rollers will have loosened on the shaft. Play can be 
eliminated by moving the stop rings on the shaft.  
 
Adjustment is easiest when Maxiroll is folded together. 
 

 

Fig. 21 

1

 

Slacken  bolts  (A)  and  push  roll-
ers together 

2

 

Tighten  and  slacken  stop  ring 
bolts  at  the  same  place  on  the 
shaft several times to ensure they 
bite firmly into the shaft. 

 

 

Wheels 

Lubricate  and  adjust  wheel  bearings  at  least  once  annually.  Check  tyre  pres-
sures at least once annually (see recommended pressure on tyre).  
 
Adjustment and lubrication of wheel bearings 
1.

 

Remove hub caps. 

2.

 

Remove split pin. 

3.

 

Tighten castle nut 1/6th of a turn until hole aligns with axle. Turn wheel, 
check  for  resistance.  A  little  play  should  be  detected  in  the  hub  housing 
when rocking wheel from side to side. If play is excessive, repeat process. 

4.

 

Replace split pin 

5.

 

Fill hub cap ¾ full with grease. Replace. 

 

Wear parts 

 

Fig. 22 

Wear  parts  (shoes)  are  factory-
mounted  in  the  upper holes on each 
tooth. Move down to the lower holes 
(A) before teeth are worn.  
 
Once they are worn out (when in the 
lower holes), replace.  
 

 

 

A 

A 

Summary of Contents for Maxiroll 1030 2008











































Reviews:

No comments

Brands by name

Popular brands

Load more brands