Daktronics SPORTSOUND 2000HD Installation Manual Download Page 53

DAKTRONICS

WARRANTY & LIMITATION OF LIABILITY

SL-02374    Rev 14  13 January 2020   Page 3 of 3 

Copyright © Daktronics, Inc. 

shall be English. The place of the arbitration shall be Sioux Falls, SD. A single arbitrator selected by the parties shall preside over 

the proceeding.  If a single arbitrator cannot be agreed upon by the parties, each party shall select an arbitrator, and those 

arbitrators shall confer and agree on the appointed arbitrator to adjudicate the arbitration. The arbitrator shall have the power 

to grant any provisional or final remedy or relief that it deems appropriate, including conservatory measures and an award of 

attorneys’ fees. The arbitrator shall make its decisions in accordance with applicable law. By agreeing to arbitration, the Parties 

do not intend to deprive any court of its jurisdiction to issue a pre-arbitral injunction, pre-arbitral attachment, or other order in 

aid of arbitration proceedings and the enforcement of any award. Without prejudice to such provisional remedies as may be 

available under the jurisdiction of a court, the arbitrator shall have full authority to grant provisional remedies and to direct the 

Parties to request that any court modify or vacate any temporary or preliminary relief issued by such court, and to award 

damages for the failure of any Party to respect the arbitrator’s orders to that effect. 

6.

Availability of Extended Service Agreement 

A.

For End User’s protection, in addition to that afforded by the warranties set forth herein, End User may purchase extended 

warranty services to cover the Equipment. The Extended Service Agreement, available from Daktronics, provides for electronic 

parts repair and/or on-site labor for an extended period from the date of expiration of this warranty. Alternatively, an Extended 

Service Agreement may be purchased in conjunction with this Warranty for extended additional services. For further 

information, contact Daktronics Customer Service at 1-800-DAKTRONics (1-800-325-8766). 

 

 

 

 

 

Additional Terms applicable to sales outside of the United States

 

 

The following additional terms apply 

only

 where the installation site of the Equipment is located outside of the United States of America. 

1.

In the event that the installation site of the Equipment is in a country other than the U.S.A., then, notwithstanding Section 5 of the Warranty, 

where the selling entity is the entity listed in Column 1, then the governing law of this Warranty is the law of the jurisdiction listed in the 

corresponding row in Column 2 without regard to its conflict of law principles. Furthermore, if the selling entity is an entity listed in Column 

1, then the place of arbitration is listed in the corresponding row in Column 3. 

 

Column 1  

(Selling Entity) 

Column 2  

(Governing Law) 

Column 3 

(Location of Arbitration) 

Daktronics, Inc.  

The state of Illinois 

Chicago, IL, U.S.A. 

Daktronics Canada, Inc. 

The Province of Ontario, Canada 

Toronto, Ontario, Canada 

Daktronics UK Ltd.  

England and Wales 

Bristol, UK 

Daktronics GmbH 

The Federal Republic of Germany  

Wiesbaden, Germany 

Daktronics Hong Kong Limited 

Hong Kong, Special Administrative Region of the P.R.C. 

Hong Kong SAR 

Daktronics Shanghai Co., Ltd. 

The Peoples Republic of China 

Shanghai, P.R.C.  

Daktronics France, SARL 

France 

Paris, France 

Daktronics Japan, Inc. 

Japan 

Tokyo, Japan 

Daktronics International Limited   

Macau, Special Administrative Region of the P.R.C. 

Macau SAR 

Daktronics Australia Pad Ltd 

Australia  

Sydney, Australia 

Daktronics Singapore Pte. Ltd 

Singapore  

Singapore 

Daktronics Brazil LTDA 

Brazil 

São Paulo, Brazil 

Daktronics Spain S.L.U. 

Spain 

Madrid, Spain 

Daktronics Belgium N. V 

Belgium  

Kruibeke, Belgium 

Daktronics Ireland Co. Ltd.  

Ireland 

Dublin, Ireland 

 

 
 
 

 
 

 

Summary of Contents for SPORTSOUND 2000HD























































Reviews: