Daktronics Galaxy Series Manual Download Page 55

Page: 55 / 90

Appendix A: Reference Drawings

A-1

Appendix A:

Reference Drawings

Refer to

Section 1.1

for information on reading drawing numbers. The following drawings are

listed in numerical order by size (A, B, etc.).

Assy; Power Termination Box .........................................................

Drawing A-127361

CAN Wiring W/Out Jacks ................................................................

Drawing A-173137

System Riser Diagram, RS422........................................................

Drawing A-174135

System Riser Diagram, RS232........................................................

Drawing A-174341

System Riser Diagram, Modem.......................................................

Drawing A-174342

System Riser Diagram, Fiber ..........................................................

Drawing A-174344

Comp. Layout; AF-3160-8/16/24/32x48-34-Mono...........................

Drawing A-177788

Comp. Layout; AF-3160-40/48x48-34-Mono...................................

Drawing A-177789

Comp. Layout; AF-3160-8/16/24/32x64-34-Mono...........................

Drawing A-177790

Comp. Layout; AF-3160-40/48x64-34-Mono...................................

Drawing A-177792

Comp. Layout; AF-3160-8/16/24/32x80-34-Mono...........................

Drawing A-177793

Comp. Layout; AF-3160-40/48x80-34-Mono...................................

Drawing A-177794

Comp. Layout; AF-3160-8/16/24/32x96-34-Mono...........................

Drawing A-177795

Comp. Layout; AF-3160-40/48x96-34-Mono...................................

Drawing A-177796

Comp. Layout; AF-3160-8/16/24/32x112-34-Mono.........................

Drawing A-177798

Comp. Layout; AF-3160-40/48/x112-34-Mono................................

Drawing A-177800

Comp. Layout; AF-3160-8/16/24/32x128-34-Mono.........................

Drawing A-177801

Comp. Layout; AF-3160-40/48x128-34-Mono.................................

Drawing A-177802

Comp. Layout; AF-3160-8/16/24/32x144-34-Mono.........................

Drawing A-177803

Comp. Layout; AF-3160-40/48x144-34-Mono.................................

Drawing A-177804

Symbols; AF-3160 Component Layout ...........................................

Drawing A-177805

Detail; AF-3160-8/16, Power/Control Corner ..................................

Drawing A-178959

Detail; AF-3160-24/32/40/48, Power/Control Corner ......................

Drawing A-178960

Power Specs, 8x48-48x128 Displays, 3 LED/pixel .........................

Drawing A-179874

Power Specs, 8x48-48x128 Displays, 4 LED/pixel .........................

Drawing A-179875

Power Specs, 8x48-48x80 Displays, RG ........................................

Drawing A-179876

System Riser Diagram, QC Outdoor Radio Gen2...........................

Drawing A-185359

Schematic, Signal Wiring, Internal, W/Quick Connect ....................

Drawing B-177662

Controller, Galaxy, 8-conn., J-1087.................................................

Drawing B-177838

Shop Drawing, AF-3160-8-32-34, Mono Gen2................................

Drawing B-178625

Shop Drawing, AF-3160-40/48**-34-Mono Gen2............................

Drawing B-178626

Schematic, AF-3160-16X***-9, Monochrome..................................

Drawing B-178693

Schematic, AF-3160-24132X***-9, Monochrome............................

Drawing B-178797

Schematic, AF-3160-40/48X***-9, Monochrome.............................

Drawing B-178821

Schematic, AF-3160-8X***-9, Monochrome....................................

Drawing B-178861

Summary of Contents for Galaxy Series



























































































Search results

Summary of Contents for Galaxy Series

Reviews:

Related manuals for Galaxy Series

Brands by name

Popular brands

Daktronics Galaxy Series, Manual

Search results

Summary of Contents for Galaxy Series

Reviews:

Related manuals for Galaxy Series

Brands by name

Popular brands