Daktronics 1000 Series Installation Manual Download | Manualshive

Page: 23 / 30

background image

Safety

19

OSHA 10 Hour for Construction

Daktronics installation personnel may face a variety of conditions on a given job site. It is

mandatory that each employee involved in installation and other field work participate in an

OSHA 10 Hour for Construction course.

OSHA 30 Hour for Construction

This course provides employees with more in-depth information on construction standards

relevant to work they may need to perform. This course is not mandatory.

First Aid/Adult CPR

First aid and adult CPR training is strongly recommended for installation personnel.

Aerial Lifts/Bucket Trucks

Daktronics employees must be trained in the safe operation, use, and inspection of aerial lifts

and bucket trucks. This course is recommended for installation personnel.

Service Platform/Ladder Way

This course covers regulations when working on, or near, service platforms and ladder ways.

This course is strongly recommended for all installation personnel.

«
...
21
22
23
24
25
...
»

Summary of Contents for 1000 Series































Reviews:

No comments

Related manuals for 1000 Series

Brand: lap Pages: 4

Brand: FIRST TEAM SPORTS Pages: 5

Brand: Rally and Roar Pages: 8

Brand: Quoizel Pages: 2

PERDIDO RFSW6300L30RSPC

Brand: HAMPTON BAY Pages: 20

Galaxy Street Eco

Brand: IPAS Pages: 3

MONTI 5293101 Series

Brand: Trio Pages: 2

Pictor Bollards

Brand: NERI Pages: 18

Brand: B-K lighting Pages: 3

FCB-XM-DG0368-29V

Brand: GE Pages: 2

Safco Mini-Scoot Mobile File

Brand: LDI Pages: 2

Brand: Vaxcel Pages: 2

Brand: palmiye Pages: 86

Brand: Gainsborough Pages: 3

Brand: Bandini Industrie Pages: 22

Skyhigh Xtreme 360

Brand: Garden Games Pages: 22

Brand: Avyna Pages: 63

Brand: Eschenbach Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands