Home
/
DaimlerChrysler
/
Jeep
/
Manual

DaimlerChrysler Jeep, Manual, Page: 125 / 467

Share

Page: 125 / 467

DaimlerChrysler Jeep Manual Download Page 125

5. Unsnap and remove the black boot cover. This cover
should be discarded. It was intended as a protective
cover for shipping only.

NOTE:

A visual instruction sheet is enclosed in the dual

top wrap.

6. Remove the swing gate bar (black metal bar for
bottom of rear window) located in the soft top and set
aside.

NOTE:

Be sure the wire harness in the right rear corner

is not tangled in the soft top bows before you lift the top.

7. Put up the soft top. Refer to “Soft Top — Putting Up
the Soft Top” in this section.

FREEDOM TOP 3– PIECE MODULAR HARD TOP

CAUTION!

•

The hard top is not designed to carry any addi-
tional loads such as roof racks, spare tires, build-
ing, hunting, or camping supplies, and/or luggage,
etc. Also, it was not designed as a structural
member of the vehicle, and thus cannot properly
carry any additional loads other than environmen-
tal (rain, snow, etc.).

CAUTION!

Do not move your vehicle until the top has been
either fully attached to the windshield frame and
bodyside, or fully removed.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

125

3

«
...
123
124
125
126
127
...
»

Summary of Contents for Jeep




















































































































































































































































































































































































































































































Reviews:

No comments