![background image](http://html1.mh-extra.com/html/daikin/super-multi-nx-g-series/super-multi-nx-g-series_service-manual_4705809054.webp)
Control Specification
SiUS12-928_A
45
Function and Control
3.2
Frequency Control
Outline
Frequency that corresponds to each room’s capacity is determined according to the difference
between the target temperature and the thermistor temperature of each room.
The function is explained as follows.
1. How to determine frequency
2. Frequency command from an indoor unit (Difference between a room thermistor temperature
and the target temperature)
3. Frequency command from an indoor unit (The ranked capacity of the operating room)
4. Frequency initial setting
5. PI control
Details
How to Determine Frequency
The compressor’s frequency is determined by taking the following steps.
1. Determine command frequency
Command frequency is determined in the following order of priority.
1. Limiting defrost control time
2. Forced cooling / heating
3. Indoor frequency command
2. Determine upper limit frequency
The minimum value is set as the upper limit frequency among the frequency upper limits of the
following functions:
Compressor protection, input current, discharge pipe temperature, low Hz high pressure limit,
heating peak-cut, freeze-up protection, defrost.
3. Determine lower limit frequency
The maximum value is set as the lower limit frequency among the frequency lower limits of the
following functions:
Four-way valve operation compensation, draft prevention, pressure difference upkeep.
4. Determine prohibited frequency
There is a certain prohibited frequency such as a power supply frequency.
Command fre
qu
ency
Limit fre
q
uency
Skip control
Upper limit f
u
nction
Compressor protection f
u
nction
Lo
w
er limit f
u
nction
Fo
u
r
w
ay
v
al
v
e operating compensation, etc.
Initial fre
qu
ency
PI control
Defrost control
Dropping f
u
nction
Inp
u
t c
u
rrent control, etc.
Upper limit fre
q
uency
FMAX
Lower limit fre
q
uency
FMIN
Tar
g
et fre
q
uency
(R2
8
31)
W
hen the shift of the fre
qu
ency is less than zero (
D
F<0)
b
y PI control,
the target fre
qu
ency is
u
sed as the command fre
qu
ency.
Summary of Contents for SUPER MULTI NX G Series
