background image

4 About the units and options

Installer reference guide

7

RZASG71~Y1
Sky Air Advance-series
4P486047-1 – 2017.04

f

Multilingual fluorinated greenhouse gases label (only for
RZASG71)

4

About the units and options

4.1

Overview: About the units and
options

This chapter contains information about:

▪ Identifying the outdoor unit

▪ Combining the outdoor unit with options

4.2

Identification

NOTICE

When installing or servicing several units at the same time,
make  sure  NOT  to  switch  the  service  panels  between
different models.

4.2.1

Identification label: Outdoor unit

Location

Model identification

Example: 

R Z A S G 140 M7 V1 B [*]

Code

Explanation

R

Air-cooled split outdoor unit

Z

Inverter

A

Refrigerant R32

SG

Mid-end series

71~140

Capacity class

M7

Model series

V1

Power supply: 1~, 220~240 V, 50 Hz

Y1

Power supply: 3N~, 380~415 V, 50 Hz

B

European market

[*]

Minor model change indication

INFORMATION

This  unit  is  not  intended  for  use  in  high  humidity,  low
ambient temperature regions. For these regions the RZAG
model is recommended.

4.3

Combining units and options

4.3.1

Possible options for the outdoor unit

Refrigerant branch kit

When connecting multiple indoor units to the outdoor unit, you need
one or more refrigerant branch kits. The outdoor‑indoor combination
determines which and how many refrigerant branch kits to use.

Layout

Model name

Twin

KHRQ(M)58T

Layout

Model name

Triple

KHRQ(M)58H

Double twin

KHRQ(M)58T (3×)

For  more  selection  details,  see  the  catalogues.  For  installation
instructions, see the installation manual of the refrigerant branch kit.

Demand adaptor kit (SB.KRP58M52)

▪ Includes the additional mounting plate (EKMKSA2)

▪ Can be used for the following:

▪ Low noise: To lower the operation sound of the outdoor unit.

▪ I-demand  function:  To  limit  the  power  consumption  from  the

system  (example:  budget  control,  limit  power  consumption
during peak moments…).

▪ For  installation  instructions,  see  the  installation  manual  of  the

demand adaptor kit.

5

Preparation

5.1

Overview: Preparation

This chapter describes what you have to do and know before going
on-site.

It contains information about:

▪ Preparing the installation site

▪ Preparing the refrigerant piping

▪ Preparing the electrical wiring

5.2

Preparing installation site

Do NOT install the unit in places often used as work place. In case
of  construction  works  (e.g.  grinding  works)  where  a  lot  of  dust  is
created, the unit must be covered.

Choose the installation location with sufficient place for carrying the
unit in and out of the site.

WARNING

The  appliance  shall  be  stored  in  a  room  without
continuously  operating  ignition  sources  (example:  open
flames, an operating gas appliance or an operating electric
heater).

5.2.1

Installation site requirements of the
outdoor unit

INFORMATION

Also read the following requirements:

▪ General  installation  site  requirements.  See  the

"General safety precautions" chapter.

▪ Service  space  requirements.  See  the  "Technical  data"

chapter.

▪ Refrigerant 

piping 

requirements 

(length, 

height

difference). See further in this "Preparation" chapter.

CAUTION

Appliance not accessible to the general public, install it in a
secured area, protected from easy access.

This  unit,  both  indoor  and  outdoor,  is  suitable  for
installation 

in 

commercial 

and 

light 

industrial

environment.

Summary of Contents for RZASG100M7V1B

































Reviews: