background image

   

Operating instructions

12

Daikin RoCon

Daikin Control unit

008.1543999_00 – 03/2017 – EN

x

 Operation

3.4.2 Setting the operating mode

The selection of the operating mode in which the Daikin heat gen-
erator is to work is made on the rotary switch in the 

"Operating 

Mode"

 

 position.

The selected operating mode is activated by briefly pressing the 
rotary button.

Set the rotary switch to the 

"Operating Mode"

 

 

position.

An overview is displayed.

Use the rotary button to select the required operating mode.

Confirm the selection with a brief push of the rotary button.

The Daikin heat generator works according to the set 
operating mode.

The current operating mode is indicated by an appropriate 
symbol on the standard display.

Standby operating mode

In this operating mode, the Daikin heat generator is switched to 
standby operation. The frost protection function remains un-
changed. In order to maintain this function, the system may not 
be disconnected from the mains.

For an outside temperature below the [T-Frost Protect] parame-
ter value, the integrated heating circulation pump is switched on 
to prevent the heating system freezing.

All controllers integrated in the RoCon system via the CAN bus 
are primarily also switched to the "Standby" operating mode.

Fig. 3-6

Displaying Info values (e.g. system pressure)

Fig. 3-7

Changing the operating mode 

(e.g. from "Standby" to "Automatic 2")

Info

Overview

Water Pressure

T-HS

Water Pressure

Operating Mode

Standby

Reducing

Operating Mode

Heating

Summer

Automatic 1

Operating Mode

Automatic 1

Automatic 2

Operating Mode

Automatic 1

Automatic 2

CAUTION!

A heating system that is not protected against 
frost can freeze in the event of frost and thus be 
damaged.

Drain the heating system on the water side if 
there is a danger of frost.

If there is a danger of frost and the heating 
system is not drained, the current and fuel 
supplies must be secured and the mains 
switch must remain switched on.

Fig. 3-8

Standard display in the [Standby] operating mode 

(above the frost limit temperature)

Summary of Contents for RoCon BF

































































Reviews: