Daikin McQuay MicroTech III Manual Download Page 4 | Manualshive

Page: 4 / 35

Daikin McQuay MicroTech III Manual Download Page 4

4

ED 15121

Limited Warranty

Consult your local McQuay Representative for warranty details. Refer to Form 933-43285Y. To find your local McQuay
Representative, go to www.mcquay.com.

Notice

© 2009 McQuay International, Minneapolis MN. All rights reserved throughout the world.

McQuay International reserves the right to change any information contained herein without prior notice. The user is
responsible for determining whether this product is appropriate for his or her application.

™ ® The following are trademarks or registered trademarks of their respective companies. Modbus is a registered
trademark of Gould, Inc. Windows is a registered trademark of Microsoft Corporation. MicroTech III is a registered
trademark of McQuay International.

Revision History

ED 15121

October 2009

Preliminary release.

Software Revision

This edition documents all versions of the standard MicroTech

®

III Chiller Unit Controller firmware and all subsequent

revisions until otherwise indicated.

Reference Documents

Company

Number

Title

Source

McQuay
International

IM 969

MicroTech III Modbus Communication Module Installation Manual

www.mcquay.com

McQuay
International

IM 1002 (50Hz )
IM 997 (60Hz)

Pathfinder

™

Air Cooled Chiller Installation Manual

www.mcquay.com

McQuay
International

OM 998

Pathfinder Air Cooled Chiller Operation Manual

www.mcquay.com

Modbus-IDA.ORG

MODBUS Application Protocol Specification V1.1b

www.Modbus.org

Modbus-IDA.ORG

MODBUS over Serial Line Specification and Implementation Guide
V1.02

www.Modbus.org

«
...
2
3
4
5
6
...
»

Summary of Contents for McQuay MicroTech III




































Reviews:

No comments