EDUS39-800-F9
Installation and Operation
FXZQ-M
35
10.3
Installation Manual / Decoration Panel
DECORATION PANEL
BYFQ60B8W1
BYFQ60B8W1U
Read this manual attentively before installation. Do not
throw it away. Keep it in your files for future reference.
Improper installation or attachment of equipment or
accessories could result in electric shock, short-circuit,
leaks, fire or other damage to the equipment. Be sure
only to use accessories made by Daikin that are specif-
ically designed for the use with the equipment and have
them installed by a professional.
If unsure of installation procedures or use, always con-
tact your dealer for advice and information.
1.
BEFORE INSTALLATION
Leave the unit inside its packaging until you reach the
installation site.
Refer to the warning symbols on the unit.
NOTE
Rotary fan
Cut off the main power before opening the grille.
Refer to the installation manual of the indoor unit for items
not described in this manual.
NOTE
To the installer
Be sure to instruct the customer how to properly operate the
system showing him or her the operation manual of the indoor
unit.
1-1
Accessories
2.
PREPARATION BEFORE INSTALLATION
For this unit, you are able to select air flow directions. To dis-
charge air in 2 or 3 directions, it is necessary to purchase the
optional blocking pad kit.
2-1
Handling of the decoration panel
To prevent any damage to the decoration panel, take care of
the following:
- Never place the panel with the front facing down.
- Never let the panel lean against a wall.
- Never put it down on a projecting object.
- Never touch or put pressure on the swing flap in order to
prevent malfunction of the swing flap.
2-2
Preparing the decoration panel for installation
1. Remove the suction grille from the decoration panel.
Push the suction grille lever in the direction of the arrow
and open the grille. (See figure 1)
Detach the suction grille from the decoration panel by
lifting the grille up approximately 45 degrees so the
grille can be removed. (See figure 2)
3.
INSTALLATION OF THE DECORATION
PANEL TO THE INDOOR UNIT
Refer to the installation manual of the indoor unit for details on
installing the indoor unit.
1 Hold the decoration panel against the indoor unit by
matching the and marks on the decoration panel with the
position of the piping section and drain section of the
indoor unit.
2 Install the decoration panel.
1 Make sure that the swing flap motor lead wire does not
come out of the groove for routing the wire inside the
indoor unit (3 locations). If it has, put it back in. (Con-
necting the decoration panel with the wire out of the
groove may cause water leakage.)
2 Provisionally tighten the 2 supplied screws approxi-
mately 5 mm (0.2 in) into the indoor unit at the side
opposite the switch box. (See figure 3)
1
Supplied screws
2
Groove for wire routing
3
Switch box
3 Slide the panel in the direction of the arrow, matching
the 2 attachment holes ( ) over the provisionally tight-
ened screws. (See figure 4)
4 Turn the decoration panel lever at the side of the indoor
unit switch box over the hook located on that switch
box. (See figure 5)
1
Lever
2
Switch box
3
Hook
5 Attach the remaining screws and tighten all 4 screws
until the thickness of the sealing material between the
decoration panel and the indoor unit is reduced to
6~8 mm (0.24~0.31 in). (See figure 6)
1
Indoor unit
2
Ceiling
3
Sealing material
4
Decoration panel
5
Air outlet
Installation manual
Screws (4x)
Summary of Contents for FXZQ-M Series
Page 1: ...EDUS 39 800 F9_a AMERICAS FXZQ M 4 Way Ceiling Mounted Cassette Unit 2 2 ...
Page 3: ...External Appearance EDUS39 800 F9_a 2 FXZQ M 1 External Appearance FXZQ07 18M ...
Page 7: ...Dimensions EDUS39 800 F9_a 6 FXZQ M 3TW30724 3 FXZQ07 18M7VJU BYFQ60B8W1 BYFQ60B8W1U ...