Daikin FC2 Installation, Use And Maintenance Manual Download | Manualshive

Page: 41 / 56

background image

Translation from original instructions

Packaged Rooftop

41

We reserve the right to make changes without any prior notice.

UATYA

4P645202-1

5.6 Aeraulic connections

The ducting must be suitably sized so as not to generate unforeseen concentrated and/or distributed head losses

that can cause drops in the handled air flow rate below the design flow rate. The head losses in the ducting must not

exceed the available pressure provided by the fans (for particular applications, consult our Technical Department).

The ducts connected to the appliance shall not contain any potential ignition source as defined by IEC

60335-2-40:2018.

5.6.1 Return and supply ducts

The units have provision for various connections of both the return duct and the supply duct.
To identify these, refer to the dimensional drawing present in the documentation of the unit.
For the connection, the closing panels with which the unit was shipped must be removed.

Fig. 12 Connection of return duct

Fig. 13 Connection of supply channels

Fig. 14 Side connection

«
...
39
40
41
42
43
...
»

Summary of Contents for FC2

























































Reviews:

No comments

Related manuals for FC2

Brand: Vectaire Pages: 10

Brand: Dimplex Pages: 8

Brand: Harbor Breeze Pages: 30

Brand: QuFresh Pages: 4

Brand: DÜPERTHAL Pages: 32

Airfusion Louisville

Brand: LUCCI Air Pages: 94

Brand: S&P Pages: 76

Brand: Kasanova Pages: 32

Brand: ZALMAN Pages: 9

Brand: Vacmaster Pages: 13

Brand: Euramco Safety Pages: 11

Brand: Bard Pages: 16

Brand: Quoizel Pages: 5

Brand: Sensor Pages: 8

Blizzard 32510019

Brand: Holmes Pages: 2

Brand: Olimpia splendid Pages: 7

Brand: Faro Barcelona Pages: 12

Brand: Field Controls Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands