Daikin ARQ Installation And Maintenance Manual Download Page 8

Page: 8 / 44

IM 1083-3

www.DaikinApplied.com

Pre-Installation Considerations – Typical Floor Unit Installation

Figure 5: Typical unit ventilator installation and louver details (see installation section for warnings and cautions)

Unit Gasket

Refrigerant Pipe Tunnel

Screws or Bolts (by others)

Weep Holes

Caulk Top And

Two Sides Of Louver

Sealed Mortar Bed

Caulk

Weep

Holes

Floor

Unit Insulating Blanket

Back Of Unit

Unit Bottom Gasket

Seal Under Unit

Bird Screen

Internal Column For

Wall Bracing (By Others)

Unit Gasket

1" End Panel w/Cut Out

Lintel (by others)

Unit Outside Air Opening

Typical VentiMatic™ Shutter Installation

Figure 6: Typical VentiMatic Shutter assembly installation (see installation section for typical warnings and cautions)

Louver

Outside

Roomside

Typical VentiMatic louver installation with shelving.

Outside

Roomside

VentiMatic Shutter Assembly

Building Wall

Summary of Contents for ARQ













































Search results

Summary of Contents for ARQ

Reviews:

Related manuals for ARQ

Brands by name

Popular brands

Daikin ARQ, Installation And Maintenance Manual

Search results

Summary of Contents for ARQ

Reviews:

Related manuals for ARQ

Brands by name

Popular brands