background image

19

17  Air Handler Low Voltage Connections

The following composite wiring diagrams detail various 

configurations in which the air handlers can be used.  

Examples include single-stage cooling and heat pump 

with single or two-stage electric heating.  All these 

configurations can be applied with convenient connections 

to outdoor thermostat applications.

The following sections are detailed:

•  Single-Stage Cooling 

•  Heat Pump 

Each diagram details the connections between room 

thermostat and the air handlers, and the connections 

between the air handlers and the Condensing Unit (or Heat 

Pump) with optional connections to Outdoor Thermostats. 

For each configuration, refer to the explanation of the 

proper jumper(s) to remove for the corresponding blower 

speed that will result in the programmed fixed speed ECM 

motor.

IMPORTANT: When matching the AMST air handlers to 

a single speed cooling or heat pump unit, remember to 

connect “Y” from the thermostat to the “Y2” on the low 

voltage terminal board.

Any equivalent thermostat can be used in place of the 

manufacturer’s thermostat part number.

Summary of Contents for AMST U1400 Series





























Reviews: