Analog Value Object Instance Summary
The following table summarizes the Analog Value Objects supported:
Table 65: Analog Value Object Instance Summary
Instance
ID
Object Name
Description
Units
Present Value
Access Type
AV0
OUTPUT SPEED
This object indicates the calculated motor speed in RPM . The corresponding drive parameter is 0102 .
RPM
R
AV1
OUTPUT FREQ
This object indicates the output frequency applied to the motor in Hz . The corresponding drive
parameter is 0103 .
Hertz
R
AV2
DC BUS VOLT
This object indicates the drive’s DC bus voltage level . The corresponding drive parameter is 0107 .
Volts
R
AV3
OUTPUT VOLT
This object indicates the AC output voltage applied to the motor . The corresponding drive parameter
is 0109 .
Volts
R
AV4
CURRENT
This object indicates the measured output current . The corresponding drive parameter is 0104 .
Amps
R
AV5
TORQUE
This object indicates the calculated motor output torque as a percentage of nominal torque . The
corresponding drive parameter is 0105 .
Percent
R
AV6
POWER
This object indicates the measured output power in kW . The corresponding drive parameter is 0106 .
Kilowatts
R
AV7
DRIVE TEMP
This object indicates the measured heatsink temperature in °C . The corresponding drive parameter is
0110 .
°C
R
AV8
KWH (R)
This object indicates, in kW hours, the drive’s accumulated energy usage since the last reset . The
value can be reset to zero . The corresponding drive parameter is 0115 .
kWh
W
AV9
KWH (NR)
This object indicates the drive’s accumulated energy usage in kW hours . The value cannot be reset .
kWh
R
AV10
PRC PID FBCK
This object is the Process PID feedback signal . The corresponding drive parameter is 0130 .
Percent
R
AV11
PRC PID DEV
This object is the Process PID output signal’s deviation from its setpoint . The corresponding drive
parameter is 0132 .
Percent
R
AV12
EXT PID FBCK
This object is the External PID feedback signal . The corresponding drive parameter is 0131 .
Percent
R
AV13
EXT PID DEV
This object is the External PID output signal’s deviation from its setpoint . The corresponding drive
parameter is 0133 .
Percent
R
AV14
RUN TIME (R)
This object indicates, in hours, the drive’s accumulated run time since the last reset . The value can be
reset to zero . The corresponding drive parameter is 0114 .
Hours
W
AV15
MOTOR TEMP
This object indicates the drive’s motor temperature, as set up in parameter Group 35 . The
corresponding drive parameter is 0145 .
°C
R
AV16
INPUT REF 1
This object sets Input Reference 1 . Control requires parameter 1103 value = COMM .
Percent
C
AV17
INPUT REF 2
This object sets either: Input Reference 2 . Control requires parameter 1106 value = COMM . Process
PID setpoint . Control requires parameter 1106 value = PID1 OUT and parameter 4010 value =
COMM .
Percent
C
AV18
LAST FLT
This object indicates the most recent fault entered in the drive’s fault log . The corresponding drive
parameter is 0401 .
None
R
AV19
PREV FLT 1
This object indicates the second most recent fault entered in the drive’s fault log . The corresponding
drive parameter is 0412 .
None
R
AV20
PREV FLT 2
This object indicates the third most recent fault entered in the drive’s fault log . The corresponding drive
parameter is 0413 .
None
R
AV21
AO 1 ACT
This object indicates Analog Output 1’s level . The corresponding drive parameter is 0124 .
Milliamps
R
AV23
ACCEL1 TIME
This object sets the Ramp1 acceleration time . The corresponding drive parameter is 2202 .
Seconds
W
AV24
DECEL1 TIME
This object sets the Ramp1 deceleration time . The corresponding drive parameter is 2203 .
Seconds
W
AV25
MBOX PARAM
This object defines the parameter to be read or written to by the mailbox function. See BV15 and
BV16 .
None
W
AV26
MBOX DATA
This object holds the mailbox function’s parameter value – a value that was read, or is to be written .
See BV15 and BV16 .
None
W
AV27
EXT PID STPT
This object sets the External PID controller setpoint . The corresponding drive parameter is 4211 .
Control requires parameter 4210, PID SETPOINT SEL, value = 19 (INTERNAL) .
Percent
C
NOTE:
For Present Value Access Types, R = Read-only,W = Writeable, C = Commandable .
Commandable values support priority arrays & relinquish defaults .
OM 1190-1 • MD4 VFD 86 www .DaikinApplied .com
f
Ieldbus
C
onTrols
Summary of Contents for ACS320
Page 115: ......