Daikin (A)5LLF Service Manual Download Page 19 | Manualshive

Page: 19 / 51

background image

Overhaul Instructions

Si50-203

18

Semi-Hermetic Single Screw Compressor Version III

9.

Removing and Disassembling The Screw Assembly Pulley

(1) Place alignment marks on the casing and main bearing holder.

Fig. 4-16 Placing alignment marks on casing and main bearing holder

(2) Removing the screw shaft

Push the screw shaft from the suction side until the bearing holder completely extends from
the discharge side. Then pull out the shaft from the discharge side. Insert one hand through
the side cap hole and support the shaft to prevent the screw shaft from damaging the casing
when the screw rotor section comes out of the casing. Use leather gloves during removal to
prevent injuries by the screw and stator.

Fig. 4-17 Removing screw shaft (1)

«
...
17
18
19
20
21
...
»

Summary of Contents for (A)5LLF




















































Reviews:

No comments

Related manuals for (A)5LLF

Brand: Clarke Pages: 20

Brand: DeVilbiss Pages: 14

Brand: MPS Pages: 2

Brand: Clarke Pages: 20

Brand: Hamron Pages: 12

Brand: CHIWAI Pages: 90

Brand: Grizzly Pages: 26

Brand: McQuay Pages: 7

Brand: VIAIR Pages: 8

Brand: California Air Tools Pages: 16

Brand: Boss Pages: 50

Brand: Certified International Pages: 5

HGX44e CO2 Series

Brand: GEA Bock Pages: 32

HG66e HC Series

Brand: GEA Bock Pages: 40

Brand: Scarlett Pages: 14

Brand: Atlas Copco Pages: 90

Brand: Atlas Copco Pages: 110

Brand: ZIPPER MASCHINEN Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands