Dahua Mobile DVR Series Page 133 User Manual Download

Page: 133 / 172

122

Parameter

Function

Schedule to set current channel as schedule record.

Record Delay System can delay the record for specified time after alarm ended.

The value ranges from 10s to 300s.

Alarm out

Enable alarm activation function. You need to select alarm output
port so that system can activate corresponding alarm device when
an alarm occurs.

Latch

System can delay the alarm output for specified time after an
alarm ended. The value ranges from 1s to 300s.

Show
message

System can pop up a message to alarm you in the local host
screen if you enabled this function.

Buzzer

Check the box here to enable this function. The buzzer beeps
when an alarm occurs.

Alarm upload System can upload the alarm signal to the center (Including alarm

center.

Message

When 3G network connection is OK, system can send out a
message when a video loss occurs.

Send Email

If you enabled this function, System can send out an email to alert
you when an alarm occurs.

5.6.3.2 Alarm

Before operation, please make sure you have properly connected alarm devices such as

buzzer. The input mode includes local alarm, IPC offline alarm.

5.6.3.2.1 Local Alarm

From main menu->Event->Alarm->Local alarm, the local alarm interface is shown as in Figure

5-31.

Figure 5-31

Summary of Contents for Mobile DVR Series













































































































































































Search results

Summary of Contents for Mobile DVR Series

Reviews:

Related manuals for Mobile DVR Series

Brands by name

Popular brands

Dahua Mobile DVR Series, User Manual

Search results

Summary of Contents for Mobile DVR Series

Reviews:

Related manuals for Mobile DVR Series

Brands by name

Popular brands