Dahua Mobile DVR Series User Manual Download Page 108

Page: 108 / 172

Figure 5-2

Please refer to the following sheet for detailed information.

Name

Function

System

It includes live, playback, alarm, setup, info and logout.

Channel

Click a channel to view realtime video.

Start talk

You can click this button to enable audio talk. Click

【

▼

】

to select

bidirectional talk mode. There are four options: DEFAULT, G711a,

G711u and PCM. After you enable the bidirectional talk, the Start talk

button becomes End Talk button and it becomes yellow.

Instant

record

Enable all-channel manual record. The record type is general.

Local

playback

Refer to chapter 5.3.5 Local playback for detailed information.

Window

mode

Refer to chapter 5.3.3 Window mode for detailed information.

Alarm output 1/2 refers to the alarm output port of the rear panel.

PTZ control Refer to chapter 5.3.4 for detailed information.

5.3.2

Monitor Window

Click a channel name, select main stream or sub stream. See Figure 5-3.

Figure 5-3

Summary of Contents for Mobile DVR Series













































































































































































Search results

Summary of Contents for Mobile DVR Series

Reviews:

Dahua Mobile DVR Series, User Manual, Page: 108 / 172

Search results

Summary of Contents for Mobile DVR Series

Reviews: