Dahua Mobile DVR Series User Manual Download Page 18

Page: 18 / 172

2 Front Panel and Rear Panel

2.1 Front Panel

The front panel is shown as in Figure 2-1.

Figure 2-1

Please refer to the following sheet for detailed information.

Name

Port and Indicator Light

RJ45 Ethernet port

1 network port.

USB port

2 USB ports to connect to mouse or flash disk to backup data.

Door

lock/unlock

(Device

on/off

button)



Please unlock the device before you remove the HDD

box. Otherwise system is going to shut down

automatically.



System cannot boot up once the button is unlock. Please

lock the device first and the boot up the device. It is to

protect the HDD.

PWR

Power indicator light.



The red light is on when the device is running.



The light is off when the device is off.

REC

Record indicator light.



The blue light is on when system is recording.



The light is off when system is not recording.

HDD

HDD indicator light.



The blue light is on when there is HDD.



The light is off when there is no HDD.

ALM

Alarm indicator light.



The blue light is on when there is an alarm.



The light is off when there is no alarm.

It is to receive the signal from the remote control.

Summary of Contents for Mobile DVR Series













































































































































































Search results

Summary of Contents for Mobile DVR Series

Reviews:

Dahua Mobile DVR Series, User Manual, Page: 18 / 172

Search results

Summary of Contents for Mobile DVR Series

Reviews: