manualshive.com logo in svg

Dahua HCVR8204A-S3, User Manual, Page: 70 / 446

Share
Download
Dahua HCVR8204A-S3 User Manual Download Page 70

 

60 

Note 

Click Add more to add more holidays if necessary.   

Step 4  Click Add button.   

Device goes back to Figure 4-17 to display the new holiday.   

Note 

  The new holiday state is on by default. Select from the dropdown list to 

disable.   

  Drag the slide bar, click 

  to edit holiday, click 

  to delete holiday.   

Note 

After successfully set holiday here, you can view holiday item in Schedule interface. It 

is for you to set holiday schedule record/snapshot settings.   

 

4.1.4.2  Network 

Before the operation, make sure the device has properly connected the network cable.   

Besides 

startup 

wizard 

and 

configuration 

wizard, 

from 

main 

menu->Setting->Network->TCP/IP, you can also go to the network interface.   

 

Step 1  From main menu->Setting->Network->TCP/IP. 

Enter TCP/IP interface. See Figure 4-19. 

Step 2  Set parameters. 

 

Network Mode: Includes multiple access, fault tolerance, and load balancing. 

Please 

note the network mode is not for product of single-Ethernet card. 

  Multiple-address mode: eth0 and eth1 operate separately. You can use the 

services such as HTTP, RTP service via etho0 or the eth1. Usually you need to 

set one default card (default setup is etho) to request the auto network service 

form the device-end such as DHCP, email, FTP and etc. In multiple-address 

mode, system network status is shown as offline once one card is offline. 

  Network fault-tolerance: In this mode, device uses bond0 to communicate with 

the external devices. You can focus on one host IP address. At the same time, 

you need to set one master card. Usually there is only one running card (master 

card).System can enable alternate card when the master card is malfunction. The 

system is shown as offline once these two cards are both offline. Please note 

these two cards shall be in the same LAN. 

  Load balance: In this mode, device uses bond0 to communicate with the external 

device. The eth0 and eth1 are both working now and bearing the network load. 

Their network load are general the same. The system is shown as offline once 

these two cards are both offline. Please note these two cards shall be in the same 

LAN.   

 

Default Network Card: Please select eth0/eth1/bond0(optional) after enable 

multiple-access function 

Summary of Contents for HCVR8204A-S3































































































































































































































































































































































































































































Reviews:

No comments