background image

Regulatory  Information    I 

 

 

Regulatory Information 

The regulatory information herein might vary according to the model you purchased. Some 

information is only applicable for the country or region where the product is sold. 

FCC Information 

 

Changes or modifications not expressly approved by the party responsible for compliance 

could void the user's authority to operate the equipment. 

FCC conditions: 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions: 

 

This device may not cause harmful interference. 

 

This device must accept any interference received, including interference that may cause 

undesired operation. 

FCC compliance: 

This equipment has been tested and found to comply with the limits for a digital device, 

pursuant to part 15 of the FCC Rules. This equipment generate, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the guide, may cause 

harmful interference to radio communication. 

 

For  class  A  device,  these  limits  are  designed  to  provide  reasonable  protection  against 

harmful  interference  in  a  commercial  environment.  Operation  of  this  equipment  in  a 

residential  area  is  likely  to  cause  harmful  interference  in  which  case  the  user  will  be 

required to correct the interference at his own expense. 

 

For  class  B  device,  these  limits  are  designed  to  provide  reasonable  protection  against 

harmful  interference  in  a  residential  installation.  However,  there  is  no  guarantee  that 

interference will not occur in a particular installation. If this equipment does cause harmful 

interference  to  radio  or  television  reception,  which  can  be  determined  by  turning  the 

equipment off and on, the user is encouraged to try to correct the interference by one or 

more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

Summary of Contents for DH-TPC-BF5601N-B


























Reviews: