background image

 

 

1.2  FCC Information 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions: 

 

This device may not cause harmful interference; 

 

This device must accept any interference received, including interference that may cause 

undesired operation. 

FCC compliance

 

This equipment has been tested and found to comply with the limits for a digital device, pursuant to 

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference. This equipment generates uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instruction manual, may cause harmful interference to radio 

communication. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

1.3  Legal Notices 

Copyright 

This user guide is ©2017, Dahua Technology Company, LTD. 

This user guide is the intellectual property of Dahua Technology Company, LTD and is protected by 

copyright. All rights reserved. 

Trademarks 

All hardware and software product names used in this document are likely to be registered 

trademarks and must be treated accordingly. 

Summary of Contents for A83ALBZ


















Reviews: