D-Link JustConnect DNR-4020-16P User Manual Download Page 45

Page: 45 / 167

D-Link DNR-4020-16P User Manual

Section 3 - Configuration

Channel

Enable

Motion

Analysis

Event Actions

Enable Alarm

Out / Camera

Alarm Out

Enable Event

Recording

Detection

Area

Detection

Schedule

Select the channel to configure.

Toggle this to cause motion detection to trigger an alarm.

Toggle this to enable or disable motion analysis.

Select the event(s) the alarm should trigger from the following
list:

•  Email: Send an email notification
•  Buzzer: Trigger a buzzer sound
•  Popup Message: Display a notification in a popup window
•  Full Screen: Display a full-screen notification on the attached

monitor

Trigger a notification on the Alarm Out interface(s).

Toggle to keep a record of alarm events.

Select the area of the display to scan for motion.

Enable or disable the alarm according to a particular schedule.

Motion Detection

Configure an alarm to trigger when the camera detects motion.

Summary of Contents for JustConnect DNR-4020-16P








































































































































































Search results

Summary of Contents for JustConnect DNR-4020-16P

Reviews:

Brands by name

Popular brands

D-Link JustConnect DNR-4020-16P, User Manual

Search results

Summary of Contents for JustConnect DNR-4020-16P

Reviews:

Brands by name

Popular brands