D-Link DAP-1533 User Manual Download Page 13

Page: 13 / 99

D-Link DAP-1533 User Manual

Section 2 - Installation

Depending on how you want to use your DAP-1533 will determine which mode you use. This section will help you figure out

which setting works with your setup.

AP.Mode

If you already have a wired or wireless router, and want to add an access point to connect your wireless clients to your network,

you will need to move the switch on the back panel of the DAP-1533 to “AP2.4GHz” (for 2.4GHz) or “AP 5GHz” (for 5GHz).

Bridge.Mode

If you want to connect multiple Ethernet-enabled devices such as game consoles, media players, or network attached storage

devices wirelessly to your wireless router or AP device, you will need to move the switch on the back panel of the DAP-1533

to “Bridge”.

AP/Bridge Mode

WIRELESS

DIR-615

WIRELESS

DIR-615

DAP-1533

Media Player

Game Console

NAS

Wireless N450

Media Bridge®/AP

DAP-1533

Router

Wired PC

WIRELESS

DIR-615

WIRELESS

DIR-615

DAP-1533

Wired PC

Router

Wireless N450

Media Bridge®/AP

DAP-1533

Summary of Contents for DAP-1533




































































































Search results

Summary of Contents for DAP-1533

Reviews:

Related manuals for DAP-1533

Brands by name

Popular brands

D-Link DAP-1533, User Manual

Search results

Summary of Contents for DAP-1533

Reviews:

Related manuals for DAP-1533

Brands by name

Popular brands