D-Link DAP-1360 User Manual Download Page 252

Page: 252 / 270

DAP-1360

Wireless N300 Access Point & Router

User Manual

Configuring Device (Router Mode)

Control

This menu is designed to create restrictions on access to certain web sites.

URL Filter

On the pages of the

Control / URL filter

section, you can specify restrictions on access to certain

web sites.

Figure 195. The

Control / URL filter / Configuration

page.

To enable the URL filter, select the

Enable/Disable URL filter

checkbox on the

Control / URL

filter / Configuration

page, then select a needed mode from the

URL filter

type

drop-down list:

•

Block listed URLs

: when this value is selected, the access point blocks access to all

addresses specified on the

Control / URL filter / Configuration

page;

•

Block all URLs except listed

: when this value is selected, the access point allows access

to addresses specified on the

Control / URL filter / Configuration

page and blocks

access to all other web sites.

Click the

Apply

button.

To specify URL addresses to which the selected filtering will be applied, go to the

Control / URL

filter / URL addresses

page.

Page

252

of 270

Summary of Contents for DAP-1360















































































































































































































































































Search results

Summary of Contents for DAP-1360

Reviews:

Related manuals for DAP-1360

Brands by name

Popular brands

D-Link DAP-1360, User Manual

Search results

Summary of Contents for DAP-1360

Reviews:

Related manuals for DAP-1360

Brands by name

Popular brands